User manual HARMAN KARDON PM645

[. . . ] To get the maximum enjoyment from your new BDS system, we urge you to read this manual thoroughly and refer back to it as you become more familiar with your new system's features and their operation. If you have any questions about this product, its installation or its operation, please contact your retailer or custom installer, or visit the Harman Kardon Web site at www. harmankardon. com. Due to the heat generated by the receiver and other components in your system, there is the remote possibility that the rubber padding on the bottom of the unit's feet may leave marks on certain wood or wood-veneer materials. Use caution when placing the unit on soft woods or other materials that heat or heavy objects may damage. Some surface finishes may be particularly sensitive to absorbing such marks, due to a variety of factors beyond harman kardon control, including the nature of the finish, cleaning materials used, normal heat and vibration caused by the use of the product, or other factors. [. . . ] Holding down the Cursor Up button quickly scans through all of the setup code numbers. If you pass the correct setup code number, you can return to it by pressing the Cursor Down button, one setup code number at a time, until the component turns back on. e) Check that the other remote-control buttons control the component as expected. If they do, press the Aux source selector button again to save the code. The button will flash three times, and the remote will exit the programming mode. f) If the remote does not operate as expected, repeat Steps c ­ e. Note that some components may not respond to all of the above commands and may support only some of the commands listed. To teach individual button codes to the remote: 1 2 5 8 0 3 6 9 1 2 5 8 0 3 6 9 1 4 7 2 5 8 0 3 6 9 4 7 4 7 + ­ + ­ + ­ + ­ + ­ + ­ ­+­ +­+ Using the Remote When using the remote, remember to aim it toward the receiver's front panel. Make sure that no objects, such as furniture, block the remote's view of the receiver. Bright lights, fluorescent lights, and plasma-video displays may interfere with the function of the remote. The remote has a range of about 20 feet (6. 1m), depending on the lighting conditions. NOTE: If the Aux button's LED goes out at any time, you will need to begin again from Step 2. Programming Remote Control "Punch-Through" Commands After programming the remote to control an auxiliary (Aux) component, you can also program it so it will control the Aux component's channel up/down and transport functions (Play, Pause, etc. ) even when the remote is not in the Aux-control mode. For example, if the 18 BDS remote is programmed to operate your TV in the Aux control mode, you can also have the TV's channel +/­ functions "punch through" and operate even when the remote is in the Disc, Radio or iPod control modes. Press and hold the button for the main device the remote will be operating. a) For "punch-through" channel control, press the Channel Up button. b) For "punch-through" transport control, press the Play button. You can repeat Step 1 ­ Step 3 for any of the remote's source-selector buttons (Aux, Radio etc. ). NOTE: "Punch-through" channel and transport commands will override the existing commands for those buttons in the source modes you program. To undo "punch-through" programming, follow the same steps as above, but press the same source selector button in Step 1 and Step 3. Previous Preparing the Remote Control and Setting Up the Receiver Please select which language you would like the BDS menus to appear. English Español Français Deutsch Italiano OK Next After setting the language you want the on-screen menus to use, press the OK button, and the Wizard's TV-resolution screen will appear. Setup Wizard Page: 3/5 Using the Remote After it is Programmed Pressing the remote's Aux source-selector button will put the remote into the auxiliarycontrol mode, and it will control the auxiliary component(s) via the codes you have programmed into it. To switch the remote back to the BDS receiver-control mode from the auxiliary-control mode, press any one of these buttons: Disc, Radio, iPod or Home. Please select the highest resolution that your TV supports. Upon making a selection the screen will be changed to the chosen resolution. You will be presented with the option to continue with the new resolution or `Cancel' to return to the previous resolution. [. . . ] Plugging the subwoofer's Power cord into the same AC outlet that the receiver is plugged into should eliminate the ground loop. Check that the disc is the correct type: BD-Video (single-layer or double-layer), DVD-Video, DVD+R/+RW, DVD-R/-RW, CDDA (CD digital audio), CD-R/RW. Press the Options button and perform the Lip Sync adjustment to bring the sound and picture into synchronization. Replace all three remote-control batteries with fresh ones, and make sure that they are installed with the correct polarity. [. . . ]