User manual HARMAN KARDON T45C

[. . . ] Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. [. . . ] The second step is to associate one of the digital inputs with the selected input source (if this is needed, otherwise the selected analog input will remain). Within five seconds, make your input selection using the buttons on the remote until the desired digital or analog input is shown in the Main Information Display . After the setting has been made with one input, repeat as described above with all inputs in use. The digital input associated with the input selected can also be changed at any time later and the AVR's memory system will keep the settings until they are changed again. 5. Turn the AVR on either by pressing the System Power Control or the Input Source Selector on the front panel, or via the remote by pressing the AVR Selector or any of the Input Selectors on the remote. The Power Indicator will turn blue to confirm that the unit is on, and the Main Information Display will also light up. NOTE: After pressing one of the Input Selector buttons to turn the unit on, press the AVR Selector to have the remote control the AVR functions. is selected, low frequency front When channel sounds will be sent only to the subwoofer output. Note that if you choose this option and there is no subwoofer connected, you will not hear any low frequency sounds from the front channels. This setting is not available with stereo mode to ensure purest sound by bypassing the crossovers of the DSP´s. When is selected, a full-range output will be sent to the front left and front right outputs. Depending on the subwoofer configuration (see below), the front left and right bass information may also be directed to a subwoofer. To make it easier to establish the initial parameters for the AVR, it is best to leave the default setting of Logic 7 Music mode for most analog inputs and Dolby Digital for inputs connected to digital sources. In the case of inputs such as a CD Player, Tape Deck or Tuner, you may wish to set the mode to Stereo, if that is your preferred listening mode for standard stereo sources, where it is unlikely that surround encoded material will be used. To set the surround mode you wish to use with the input selected, press the Surround Mode Selector button on the front or on the remote until the desired surround mode´s name appears in the Main Information Display . Note that Dolby Digital and DTS will only appear as choices when a digital input has been selected. After the surround mode setting has been made with the current input, repeat the setting with all inputs you will use. The surround mode can also be changed at any time later, and the AVR's memory system will keep the settings for the input selected, until they are changed again. If no subwoofer is connected to the AVR, press the arrow buttons so that appears in the display. When this option is selected, all bass information will be routed to the front left/right "main" speakers. If a subwoofer is connected to the AVR, you have the option to have the front left/right "main" speakers reproduce bass frequencies at all times, and have the subwoofer operate only when the AVR is being used with a digital source that contains a dedicated Low Frequency Effects, or LFE soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies. To select that option press the arrow buttons so that appears in the display. If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speakers, regardless of the type of program source or surround mode you are listening to, press the arrow buttons so that appears in the display. [. . . ] While the PTY is shown, press the Preset Up/ Down button or hold them pressed to scroll through the list of available PTY types. To simply search for the next station transmitting any RDS data, use the Preset Up/Down button until appears in the display. The tuner begins to scan the FM band upwards or downwards for the first station that has RDS data that matches the desired selection, and acceptable signal strength for quality reception. The tuner will make up to one complete scan of the entire FM band for the next station that matches the desired PTY type and has acceptable reception quality. [. . . ]