User manual HOLMES HASF1750RC

[. . . ] The use of attachments not recommended or sold by The Holmes Group may cause hazards. 14) WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state speed control device. 15) DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. All servicing should be performed by qualified personnel only. PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug having one blade wider than the other). [. . . ] Step 3: Replace blade, tighten the fan blade nut, and securely fasten the front grill. FAN STORAGE Your fan can be stored in the off-season either partially disassembled or assembled. · If stored disassembled, we recommend using the original (or appropriately sized) box. · If stored assembled or partially assembled, remember to protect the fan head from dust. H A B C D E F G J ASSEMBLY INSTRUCTIONS: I K L M N Base / Pole Assembly Step 1: Insert the lower pole (longer of the 2 poles) through the base cover and twist the pole clockwise to lock in position. Be careful to align the cut-away grooves on the threaded joint (male end) with the two protruding raised pieces inside the hollow end of the base cover. Step 2: Turn the base cover upside down (with the lower pole facing the floor) and place the weighted insert into the base cover. NOTE: HOLD THE POLE, BASE COVER AND WEIGHTED INSERT IN ONE HAND WHILE TIGHTENING THE BASE NUT WITH THE OTHER HAND. Step 3: Place the base nut on the threaded section and hand-tighten the base nut to securely fasten the lower extension pole to the base. Step 4: Insert the upper pole (shorter of the two poles) with the threaded joint (male end) into the hollow end of the lower pole (female end), until both poles meet. Be careful to align the cutaway / grooves on the threaded joint (male end) with the two protruding pieces inside the hollow end of the lower pole (female end). Step 5: Turn the upper pole clockwise to lock it securely in place. FIGURE 1 A. Logo Plate Front Grill Grill Caps Fan Blade Cap Fan Blade Rear Grill Mounting-ring G. Weight Nut O P Q Fan Head Assembly Step 1: Position the rear grill over the motor shaft, making certain the 2 notches at the top and bottom of the rear grill fit over the 2 protruding notches on the motor housing. Please make sure the rear grill fits securely against the motor housing. Step 2: Fasten the rear grill in place using the rear grill mounting-ring. Step 3: Slide the fan blade; with the hollowed interior of the fan blade facing toward the rear grill firmly onto the motor shaft. Step 4: Secure the fan blade onto the motor shaft by turning the fan blade cap counter-clockwise. Step 5: Snap the logo plate on to the front grill, making sure the clips on the logo plate, fit into the openings on the front grill. Step 6: On the front grill, lift the grill clips up so that there is no interference when placing the front grill onto the rear grill. Center the front grill, aligning the Holmes logo so it is horizontal and parallel to the floor. Hang the front grill onto the rear grill and close all of the clips until the two grills are secured. Final Assembly Step 1: Place the hollow end of the remote control housing on to the upper pole until it will not go down any further. Step 2: Tighten the locking nut on the back of the remote control housing by turning it clockwise until the fan head assembly is secure. Remote Control Handheld Unit: Your remote control requires 2 AAA batteries for operation. [. . . ] Within the first 5 years from date of purchase, subject to the conditions in paragraph H, Holmes will repair or replace the product if it is defective in material or workmanship providing it is returned to Holmes, freight prepaid, with PROOF OF PURCHASE date, together with $10. 00 for handling and return packing/shipping charges. If you have any problem with this product, please write our Consumer Service Dept. IMPORTANT Return INSTRUCTIONS Your warranty depends on your following these instructions if you are returning the unit more than 30 days after the date of purchase: 1. Carefully pack the item in its original carton or other suitable box to avoid damage in shipping. [. . . ]