User manual HOLMES HASF2219

[. . . ] (Alternating Current) PLUG (a plug having one blade wider than the other). If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact an electrician to replace the obsolete outlet. DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG ASSEMBLY INSTRUCTIONS: Base Assembly: You will need the base and four extension legs. Figure 1 Fan Head Assembly: You are now ready to assemble the fan head (See Figure #3) Step 1: Position the rear grill over the motor shaft, making certain the 2 notches at the top and bottom of the rear grill fit over the 2 prongs on the motor housing. [. . . ] Lastly, insert the tilt adjustment knob into the neck joint and tighten in place. Figure 6 Fan Blade Cleaning: (See instructions for fan head assembly on page 2, figure 4 ) STEP 1: To access the fan blade, remove the front grill and blade cap. STEP 2: Clean the fan blade, front and rear grills with a soft, moist cloth. STEP 3: Replace blade, tighten blade cap, and securely fasten the front grill. Fan Post Screw Screw Hole Fan Head, Base, and Pole Cleaning: Extension Pole Using a soft, moist cloth, with or without a mild, soap solution, carefully clean the fan base, pole, and head. Do not allow the motor or other electrical components to be exposed to water. NOTE: If your fan does not have a screw hole in the extension pole but instead has an indentation around the top of the pole; please do the following: Step 1: First, place the fan head assembly onto the extension pole and tighten the fan post screw until a secure fit is obtained. Step 2: Insert the tilt adjustment knob into the neck joint and tighten in place. FAN STORAGE: Your fan can be stored in the off-season either partially disassembled or assembled. · If stored disassembled, we recommend using the original (or appropriately sized) box. · If stored assembled or partially assembled, remember to protect the fan head from dust. The exclusive Holmes Products FanBonnet is available to protect your fan. OPERATING INSTRUCTIONS: Step 1: Set fan base on a dry, level surface. Selector (Speed) Control is located on the top of the Fan Motor Housing. Step 3: The SPEED is adjusted by turning the control knob to the desired setting, Off-High-Med-Low. Step 4: The OSCILLATION Control knob is located on the top of the Fan Motor Housing. To Stop Oscillation, Pull Control knob up. ADJUSTMENT INSTRUCTIONS: Tilt Adjustment: Follow these instructions to tilt the Fan Head for upward angle air movement. STEP 1: To change the tilting angle of the fan head, simply loosen the Tilt Adjustment Knob (see fig. 4). STEP 2: Move the fan head to the desired angle, then firmly tighten the knob to lock in place. Height Adjustment: Follow these instructions to adjust the height of the fan. STEP 1: Turn the extension pole base collar (see figure 3 and 5 on Page 2) counter-clockwise to loosen pole. STEP 2: Adjust the pole to the desired height, and firmly tighten collar in a clockwise direction. CLEANING/MAINTENANCE INSTRUCTIONS: Follow these instructions to correctly and safely care for your Holmes Products© stand fan. Please remember: · Always unplug the fan before cleaning or disassembling. · Be sure to use a soft cloth moistened with mild soap solution. · Do not use any of the following as a cleaner: gasoline, thinner, or benzine. FAN SERVICE INSTRUCTIONS: 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. [. . . ] IMPORTANT RETURN INSTRUCTIONS Your warranty depends on your following these instructions if you are returning the unit more than 30 days after the date of purchase: 1. Carefully pack the item in its original carton or other suitable box to avoid damage in shipping. 2. Before packing your unit for return; be sure to enclose: a) your name, full address with zip code and telephone number, b) a dated sales receipt or PROOF OF PURCHASE, c) your $15. 00 check for return shipping and handling, and d) the model number of the unit and the problem you are having. (Enclose in an envelope and tape directly to the unit before the box is sealed. ) 3. [. . . ]