User manual HOLMES HAWF2072

[. . . ] (Alternating Current) PLUG (a plug having one blade wider than the other). If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact an electrician to replace the obsolete outlet. DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG PRE-INSTALLATION INSTRUCTIONS: Carefully unpack all contents of carton. [. . . ] Match your window measurement with the installation guide (see figure #2 text); adding the appropriate extender panel(s) to the left side, while using the built-in extender on the right side. Once you have added extender panel(s) if necessary, set the fan in the window, and complete the installation process using the built-in extender. Carefully close the window onto the top of the fan so that the bottom edge of the window rests behind top line of fan housing. Page2 24" UNIT'S LENGTH PULLS OUT UP TO 5. 0" Two 3. 5" extenders, (Included in your box packed at both ends) OPERATING INSTRUCTIONS: Figure 2 · Make sure rotary switches are in the OFF position. · Set the individual fan motors on either INTAKE or EXHAUST using the control lever. · To start the unit, turn the rotary switches to desired speed (HI, MED, LO, SLEEP). Note: · If unit will not start, please check that Comfort Control Thermostat is set to HI/largest dot. (Figure 3) · When operating both fans on EXHAUST, set the Comfort Control Thermostat all the way to high by turning the dial to the right toward the largest dot. · To start oscillation, simply move the Oscillation Switch to the ON position. The oscillation system is powered by its own separate motor; therefore, both fans will oscillate when the feature is turned ON (you can set each individual fan to any speed you desire, including OFF, and both fans will oscillate. ) To end oscillation, move the switch to the OFF position. Note: Remember to turn the oscillation switch to OFF when fan is not in use. THERMOSTAT INSTRUCTIONS: Your window fan is equipped with a Comfort Control Thermostat that automatically turns the fan ON and OFF depending on the preset comfort level. FIGURE 3 · While the Window Fan is on, turn the Comfort Control Thermostat dial to the left LO COMFORT CONTROL HI toward the smaller dots until the fan (and oscillation) stops (Away from Cooler). · If the fan is stopped and you want to turn COMFORT CONTROL it back on, turn the Comfort Control Thermostat dial to the right towards the larger dots until the fan starts, (Towards Cooler). Turning dial (as noted above) helps you locate the prevailing temperature on the dial. IMPORTANT: If you desire continuous running of the fan, the Comfort Control Thermostat dial should be turned all the way to the right to the largest dot. · WARNING: BE SURE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON FAN WHILE IT IS IN THE WINDOW. FAN SERVICE INSTRUCTIONS: 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. If you have any questions regarding this unit's operation or believe any repair is necessary, please call 1-800-5 HOLMES to speak with a Customer Service Representative. If you need to exchange the unit, please return it in its original carton, with a sales receipt, to the store where you purchased it. If you are returning the unit more than 30 days after the date of purchase, please see the enclosed warranty. If you have any other questions or comments, feel free to write us: Holmes Products P. O. [. . . ] If you have any problem with this product, please write our Customer Service Dept. , or call, 1-800-5-HOLMES. IMPORTANT RETURN INSTRUCTIONS Your warranty depends on your following these instructions if you are returning the unit more than 30 days after the date of purchase: 1. Carefully pack the item in its original carton or other suitable box to avoid damage in shipping. Before packing your unit for return; be sure to enclose: a) your name, full address with zip code and telephone number, b) a dated sales receipt or PROOF OF PURCHASE, c) your $12. 50 check for return shipping and handling charges, and d) the model number of the unit and the problem you are having. [. . . ]