User manual HUMAX DV-1100S

[. . . ] Notice ** Copyright (Copyright © 2001 HUMAX Corporation) ** Not to be copied, used or translated in part or whole without HUMAX's prior consent in writing except approval of ownership of copyright and copyright law. All rights reserved. ** Warranty ** The information in this document is subject to change without notice. HUMAX does not have any responsibility for direct, indirect, accidental, necessary and other damage due to your offer or use of the information contained in this manual. ** Trademarks ** VIACCESSTM is a trademark of France Telecom. DTS and DTS Digital Out are trademarks of Digital Theatre Systems Inc. [. . . ] If antenna is not correctly set, you cannot search channel, therefore, you cannot watch a programme, either. Select Antenna Setting using the or button to enter Antenna Setting. Note: If no satellite is registered from Antenna Setting menu, Channel Search such as Automatic Search, Manual Search, Multiple Manual Search, Advanced Search is not available. Satellite You can select satellite for Channel Search. Select the satellite that is the antenna heads for from the alphabetically sorted satellite list using the button, and press the OK button. GB 57 8. If no desired satellite exists in the list, select User Define Satellite item. When you are prompted to select whether or not to edit User Define Satellite, select Yes, and press the OK to display keyboard to edit the Name. Enter Satellite Name directly, select OK, and press the OK button. Satellite Alternative You can search and watch a programme by using the antenna headed for the selected satellite. Select Satellite Alternative using the button, and press the OK or button. Then, you can change into one of the following options. ** Disable Enable Does not search the selected satellite. Searches the selected satellite. Note: If there is no satellite that Satellite Alternative is set to Enable, Channel Search is not available. LNB Frequency (MHz) You can enter LNB Frequency. Select one value from Universal, 9750, 10600, 5150, 11475, User Define using the button. If you have selected User Define, enter LNB Frequency value directly, and press the OK button. Note: If you have selected Universal, select 9750/10600. In this case, the 22kHz tone value is disabled. GB 58 * ** 22kHz Tone You can select whether or not to use 22kHz Tone. Select whether or not to use 22kHz Tone using the OK button. ** or Enable Disable Selects Enable if Dual LNB is used or 2 antennas are connected to the 22kHz tone switch box. Selects Disable if 22kHz Tone is not used. DiSEqC Input You can select DiSEqC switch. You can select one option among Tone burst A~B, DiSEqC A~D, DiSEqC A~D for 2. 0 and Disable. LNB Voltage You can raise the LNB Voltage value (select high ) preparing for the distance between antenna and receiver is further than 60m. Caution: If your set the LNB Voltage value as High when the distance between antenna and receiver is close, the LNB may be damaged. Set the LNB Voltage value using the OK ** or button. Standard High if the distance between antenna and receiver is within 60m if the distance between antenna and receiver is further than 60m GB 59 8. If you change the setting value to High, a message will prompt you to confirm. When the value is set to High, 1V higher than LNB voltage is supplied to LNB. 8. 2 Automatic Search If you select the satellite to search channel according to the Antenna Setting, you can automatically search the satellite without entering any other information. Select Automatic Search from Installation menu using the button, and press the OK or button. or Satellite You can select which satellite to search the channel. Note: Channel Search is performed only for the satellites that have been set to Enable in Antenna Setting - Satellite Alternative menu. [. . . ] LNB In Port is inserted by alien substance or damaged. GB 110 Appendix 3. Specification ** Tuner & Channel Input Connector Frequency Range Signal Level LNB Power & Polarisation F-type, IEC-169-24, Female 950MHz to 2150MHz -10 to -93dBm Vertical: +13. 5V (+14. 5V at high voltage) Horizontal: +18V (+19V at high voltage) Current: 500mA Max. Overload Protection 22kHz Tone DiSEqC Control Demodulation Input Symbol Rate FEC mode MPEG Transport Stream A/V Decoding Transport Stream MPEG-2 ISO/IEC 13818 Transport Stream Specification Profile Level Video Input Rate Aspect Ratio Video Resolution Audio Decoding Audio Mode Memory Flash Memory Graphic (MPEG) & System DRAM EEPROM Available Disc(DVD) Available Reading MP3/Audio CD/VCD/CD/CD-R, RW/DVD-R, RW/DVD+R, RW, SVACD 4M byte 16M byte 16K byte MPEG2 MP@ML 15 Mbit/s Max 4:3, 16:9 , Letter box 720x576, 720x480 MPEG/MusiCam Layer I & II Single channel/Dual channel/Joint Stereo/Stereo Frequency: 22±4kHz Amplitude: 0. 6±0. 2V Version 1. 0 Compatible, USALS QPSK 1~45 Ms/s Convolutional Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8 with Constraint Length K=7 GB 111 Appendix 3. Specification ** A/V & Data In/Out Video Audio R/L RCA/SCART Video Output(CVBS, RGB, YPbPr) RCA/SCART Volume and Mute Control (Resolution: 20 bits DAC, MAX. [. . . ]