User manual HUMMINBIRD MATRIX 17

[. . . ] Operations Manual 531369-1_A Matrix 12 Matrix 10 Matrix 17 Matrix 20 Matrix 27 Matrix 37 Thank You! Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® does require repairs, we offer an exclusive Service Policy - free of charge during the first year after purchase, and available at a reasonable rate after the one-year period. [. . . ] Exit the Simulator by powering your Fishing System off. Simulator, Shown with Optional WeatherSenseTM Accessory System Status Accessory Test Screen Exit System Status by powering your Fishing System off. PC Connect (With PC Connect Cable Only) Use PC Connect to update the software of the Matrix control head. Complete instructions are included with the PC Connect Cable accessory. NOTE: The PC Connect Cable requires a separate purchase. For more information visit our website at www. humminbird. com or contact our Customer Resource Center at 1-334-687-0503. Exit PC Connect mode by powering the Fishing System off. 21 22 Sonar X-PressTM Menu The Sonar X-Press Menu provides access to the settings most frequently-used. Press the MENU key once while in any of the Sonar Views to access the Sonar X-PressTM Menu. NOTE: Upper Range only appears in Advanced User Mode when in Sonar, Split Sonar or Big Digits View. NOTE: Zoom Level only appears in Sonar Zoom View. TM To adjust the Sensitivity: 1. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Sensitivity setting. (Low = 1, High = 20, Default = 10) Upper Range (Advanced: Sonar, Split Sonar and Big Digits Views Only) Upper Range sets the shallowest depth range that will be displayed on the Sonar, Split Sonar and Big Digits Views. The Upper Range menu choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode) and can only be accessed from the Sonar, Split Sonar and Big Digits Views. Upper Range is often used with Lower Range. For example, if you are only interested in the area between 20 and 50 feet deep, you should set the Upper Depth Range to 20 and the Lower Depth Range to 50. The Sonar View will then show the 30 foot area between 20 and 50, and will not show the surface or the bottom (assuming the bottom is deeper than 50 feet), and will show greater detail for that area between 20 and 50 feet. NOTE: A minimum distance of 10 feet will be maintained between the Upper and Lower Range regardless of the manual settings entered. Sonar X-PressTM Menu Sensitivity Sensitivity controls how much detail is shown on the display. Increasing the sensitivity shows more sonar returns from small baitfish and suspended debris in the water; however, the display may become too cluttered. When operating in very clear water or greater depths, increased sensitivity shows weaker returns that may be of interest. Decreasing the sensitivity eliminates the clutter from the display that is sometimes present in murky or muddy water. If Sensitivity is adjusted too low, the display may not show many sonar returns that could be fish. To adjust the Upper Range: 1. Make sure you are in Advanced Mode, then highlight Upper Range on the Sonar X-PressTM Menu. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Upper Range setting. (0 to 790/990/1490 feet or 0 to 257/327/497 meters [International Models Only], Default = 0) NOTE: Settings are dependent on the depth capability of your particular Fishing System model. Sensitivity at Low Sensitivity at Medium Sensitivity at High 23 24 Lower Range Lower Range sets the deepest depth range that will be displayed. When in automatic mode, the lower range will be adjusted by the unit to follow the bottom. Use both Upper and Lower Range together to view a specific depth range manually when looking for fish or bottom structure. M will be displayed in the lower right corner of the screen when you start manually adjusting the Lower Range to indicate that you are in Manual mode. For example, if you are fishing in 60 feet of water but are only interested in the first 30 feet (surface to a depth of 30 feet) you should set the Lower Depth Range limit to 30. The display will show the 0 to 30 foot range, allowing you to see a more detailed view than you would see if the display went all the way to the bottom. [. . . ] One or more of the following sources can cause noise or interference: Possible Source of Noise Other electronic devices Matrix Fishing System Accessories Accessories customize the Matrix Fishing System to your needs and enable you to stay on the edge of new technology. When an accessory is connected to the Matrix Fishing System, additional menus and readouts are added automatically to the Main Menu System. Accessories available today that are supported by your Fishing System include: Temperature/Speed: purchase and plug in the Temperature/Speed accessory to your Matrix control head to get real time speed and temperature readouts, as well as a valuable Triplog function. NOTE: If an external Temperature/Speed (TS-W) or Temperature (TG-W) accessory is connected AND a transducer with temperature built in is connected at the same time, the TS-W or TG-W accessory will override the temperature which is built in to the transducer. Isolation Turn off any nearby electronic devices to see if the problem goes away, then turn them on one at a time to see if the noise re-appears. To determine whether the boat's engine is the source of the noise, increase the RPMs while the boat is in neutral and stationary to see if the noise increases proportionately; if noise appears when you rev the engine, the problem could be the spark plugs, alternator, or tachometer wiring. [. . . ]