User manual HUSQVARNA 130BT

[. . . ] 130BT-380BTS_English. fm Page 1 Wednesday, December 9, 2009 10:21 AM WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. Operator’s manual APPLICABLE SERIAL NUMBERS: 00100101 and up 130BT 350BT 370BTS 380BTS Original Instructions English 115 31 90-26 130BT-380BTS_English. fm Page 2 Wednesday, December 9, 2009 10:21 AM English EC-declaration of conformity EC-declaration of conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the blowers Husqvarna 130BT, 350BT, 370BTS, 380BTS with serial numbers dating 2010 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE: - of May 17, 2006 “relating to machinery” 2006/42/EC. - of December 15, 2004 “relating to electromagnetic compatibility” 2004/108/EC, and applicable supplements. - of May 8, 2000 “relating to the noise emissions in the environment” 2000/14/EC. For information relating to noise emissions, see the chapter Technical data. [. . . ] The difference between guaranteed and measured sound power is that the guaranteed sound power also includes dispersion in the measurement result and the variations between different machines of the same model according to Directive 2000/14/EC. Note 2: The equivalent sound pressure level value is calculated with a work cycle of a duration of 1/7 for idling and 6/7 for racing. Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation) of 1 dB(A). Note 3: The equivalent Vibration total value is calculated with a work cycle of a duration of 1/7 for idling and 6/7 for racing. Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s2. 13 130BT-380BTS_English. fm Page 14 Wednesday, December 9, 2009 10:21 AM English Assembly ■ FLEXIBLE HOSE AND SWIVEL JOINT 1. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. (1) Flexible hose (2) Swivel Joint (3) Clamp (large) (4) Clamp (small) NOTE A light lubricant may be used to ease assembly of flexible hose to blower tube. (4) (2) F1 (3) (1) ■ CONTROL HANDLE 1. Set up the handle holder to the swivel joint and tighten the knob on the holder. When setting up the handle holder, please make sure to match the handle holder to the convex on the swivel joint as shown in F2. Adjust the position and angle to achieve a comfortable working position, and tighten the control handle. (1) F2 (2) (1) Cabling (2) Flexible Hose ■ CABLING 130BT • Fasten the cabling at central position of the hose by the band attached to the cabling. First, wrap the flexible hose with the band fixed to the cabling from the lower side. Then, pass the band through a hole of the band as shown in figure. Please note that there is a possibility of damaging the flexible hose if the band is fastened too tightly. F3 (130BT) 350BT, 370BTS, 380BTS • Use the clamp to fasten the cabling to the flexible hose. (1)Clamp F4 (1) (350BT, 370BTS, 380BTS) ■ HANDLEBAR (OPTION) 1. Insert the holder, then assemble the handlebar (OPTION) and tighten it securely. F5 ■ BLOW PIPES Conect the swivel joint, straight pipe and pipe end. Push the pipes together and turn them so they lock in relation to one another until the connection is locked. NOTE A light lubricant may be used to ease assembly of the blower tube. NOTE If longer tube is required, the second straight pipe can be connected with the first one. If higher air speed is required, the round blow pipe can be replaced by the flat nozzle with the second straight pipe. (1) Flat nozzle (option). F6 F7 (1) 14 130BT-380BTS_English. fm Page 15 Wednesday, December 9, 2009 10:21 AM English Assembly ■ HARNESS. WARNING The harness must always be worn when working with the machine. Failure to do so means you will be unable to maneuver safely and this can result in injury to yourself or others. A correctly adjusted harness and machine significantly facilitates the work. [. . . ] Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. • Plug manufacturers recommend replacing the plug twice a year to avoid unexpected plug failure in a job. IMPORTANT • Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged. • To install the spark plug, first turn the plug with your hands until it is tight, then tighten it a quarter turn more with a socket wrench. [. . . ]