User manual HUSQVARNA 2009

[. . . ] H U SQVARNA AUTOMOWE R ™ 210 C OPE R ATOR’S MAN UAL TABLE OF CONTENTS 1. Introduction and safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 Symbols on Automower™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] As long as the total length of the boundary wire does not exceed 350 m (1200 ft), the sections where the wires run in parallel can be any length. For example, it is possible to place the loop generator/charger inside the house and run the boundary wire through a window and out to the garden. IMPORTANT INFORMATION Pay particular attention not to cross the boundary wire in towards the loop generator/charger. Joining the boundary wire If the boundary wire is not long enough and needs to be spliced: Use original solderless coupler. Use a pair of pliers or the like, as the button on the connector is difficult to press down by hand. IMPORTANT INFORMATION Twisted cables, or a screw terminal (chock-block), insulated with insulation tape is not a satisfactory splice. Soil moisture will cause the conductors to oxidize and after a while result in a broken circuit. 24 - English 3. INSTALLATION 3. 5 Connecting the boundary wire Connect the boundary wire to the loop generator/charger: 1. • Place the wire in the connector grip. 2. Press the connector together using a pair of pliers. Press until you hear a click. 3. Cut off any surplus boundary wire. Cut 1 à 2 cm (0. 4" - 0. 8") above respective connectors. English - 25 3. Attach the connector to the contact pin on the loop generator/charger. 3. 6 Checking the installation Check the loop signal by looking to see what indication the green LED on the loop generator/charger is giving. Flashing once every other second = break in the loop and no signal found. This may be due to the boundary wire exceeding 1200 ft or that the cable is damaged. If the mower works, it is not a problem. 3. 7 Linking the Automower™ to the loop generator/charger 1. Connect the loop generator/charger charging cable to the mower's charger contact. At most the mower may be two metres from the working area's boundary wire and the loop generator/charger must be connected to the mains supply. Set the main switch to the ON position. 6 ft 2. 26 - English 3. The yellow indicator lamp PIN code flashes once, and then remains unlit. When you have selected a PIN code, the mower and loop generator/charger are linked to each other and the mower can be operated. English - 27 4. Use 4. 1 Starting Automower™ WARNING Read the safety instructions before you start your Automower™. WARNING Keep your hands and feet away from the rotating blades. Never put your hands or feet close to or under the body when the motor is running. 1. 4. Press the STOP button to open the control panel cover on Husqvarna Automower™. Close the cover. 5 beeps are heard over 2 seconds when the blade disc starts. 4. 2 Stopping Automower™ 1. [. . . ] 40 Check the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Cleaning Automower™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Blade disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]