User manual HUSQVARNA 323 R

[. . . ] Operator's manual (EPA II) 323R 325RX-SERIES 325RXT-SERIES 325RDX-SERIES Please read these instructions carefully and make sure you understand them before using the machine. English SYMBOL EXPLANATION Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always wear approved protective gloves. Use anti-slip and stable boots. Always use • A protective helmet where there is a risk of falling objects • Ear protection • Approved eye protection Only use non-metallic, flexible cutting elements, that is trimmer head with trimmer cord. Other symbols/decals on the machine refer to special certification requirements for certain markets. Max. [. . . ] Tighten the screws. Assembling the handlebars (325RX, 325RXT, 325RDX) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Fit the screw through the throttle handle and the handlebars and tighten. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it‘s attached to the harness. Tighten the handle. Transport position, handlebars (325RX, 325RXT, 325RDX) • The handlebars can easily be turned to fit along the shaft for easy transportation and storage. Turn the handles clockwise so that the throttle comes against the engine. • Attach the transport guard. English – 17 ASSEMBLY Assembly of the blade and trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury. Assembling the blade guard and clearing blade • Remove the mounting plate (H). Fit the blade guard (A) to the adapter using the 4 screws (L) as shown. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. Hold the handle of the spanner as close to the blade guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (lefthand thread). • When slacking off and tightening the saw blade nut, the hands may be injured by the blade teeth. The illustration shows the area in which you should keep the box spanner. ! WARNING!Do not attach any blade to the unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders. Under no circumstances may the cutting equipment be used without an approved guard fitted. If the wrong guard or a defective guard is fitted this can cause serious personal injury. IMPORTANT INFORMATION The machine must be equipped with the correct handlebars, blade guard and harness if either a clearing blade or grass blade are to be used. G F Assembling the blade guard and grass blade • Hook the guard (A) onto the bracket on the shaft G and secure with 1 bolt. A B • Turn the blade axle until C one of the holes in the drive disc aligns with the hole in the gear housing. [. . . ] speed, left/right handles, max: 323R 1, 50/24, 5 1, 34/34 1, 06/27 2 700 11 000-11 700 8 014 0, 9/ 9 000 No Yes 325RX 1, 50/24, 5 1, 34/34 1, 06/27 2 700 11 000-11 700 8 014 0, 9/ 9 000 Yes Yes 325RXT/325RDX 1, 50/24, 5 1, 34/34 1, 06/27 2 700 11 000-11 700 8 014 0, 9/ 9 000 Yes Yes Walbro MB 20 Champion RCJ 7Y 0, 02/0, 5 Walbro MB 20 Champion RCJ 7Y 0, 02/0, 5 Walbro MB 20 Champion RCJ 7Y 0, 02/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 9, 9/4, 5 9, 9/4, 5 10, 8/4, 9 88/97 105/109 105/109 2, 0/2, 0 3, 2/2, 7 2, 2/2, 5 6, 0/8, 5 1, 6/1, 4 2, 0/2, 6 2, 0/2, 4 4, 8/4, 0 1, 8/1, 8 2, 2/2, 6 2, 0/2, 4 4, 8/5, 6 Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idling and 1/2 max speed. Sound pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. English – 29 TECHNICAL DATA Approved accessories 323R Centre hole in blades Ø 25, 4 mm Threaded blade axle M10 Grass blade Saw blade Plastic knives Trimmer head Type Cutting attachment guard Art No. 503 93 42-02 503 93 42-02 537 02 21-01 503 93 42-02 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 - Support cup Grass 255-4 1" (∅ 255 4-teeth) Grass 255-8 1" (∅ 250 8-teeth) Maxi X 200-26 1" (∅ 200 26-teeth) Tricut ∅ 300 Trimmy Fix Trimmy H II 1" Trimmy Hit Trimmy Hit Pro Superauto II 1" Fixed Approved accessories 325RX, 325RXT, 325RDX Centre hole in blades Ø 25, 4 mm Threaded blade axle M10 Grass blade Type Cutting attachment guard Ref No. Saw blade Plastic knives Trimmer head Support cup Grass 255-4 1" (∅ 255 4-teeth) Grass 255-8 1" (∅ 250 8-teeth) Multi 255-3 1" (∅ 255 3-teeth) Maxi X 200-26 1" (∅ 200 26-teeth) Tricut ∅ 300 Trimmy Fix Trimmy H II 1" Trimmy Hit Trimmy Hit Pro Superauto II 1" Fixed 503 93 42-02 503 93 42-02 503 93 42-02 537 02 21-01 503 93 42-02 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 - 30 – English EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. [. . . ]