User manual HUSQVARNA 954140010D

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA 954140010D. We hope that this HUSQVARNA 954140010D user guide will be useful to you.


HUSQVARNA 954140010D : Download the complete user guide (1415 Ko)

Manual abstract: user guide HUSQVARNA 954140010D

Detailed instructions for use are in the User's Guide.

[. . . ] YTH180 This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual. Owner’s Manual SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. • • • • • • • • • • • • • • • GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. [. . . ] (When using a cone balancer, follow the instructions supplied with balancer). • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. The lobes of the center hole may appear to be centered, but are not. CENTER HOLE 5/8" BOLT OR PIN BLADE BLADE CARE For best results mower blades must be kept sharp. 16) • • • • • Raise mower to highest position to allow access to blades. Install new or resharpened blade with trailing edge up towards deck as shown. Reassemble hex bolt, lock washer and flat washer in exact order as shown. torque). BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Clean terminals and battery cable ends with wire brush until bright. • Reinstall battery (See “CONNECT BATTERY” in the Assembly section of this manual). IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED. NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. BLADE MANDREL ASSEMBLY TRAILING EDGE FLAT WASHER LOCK WASHER HEX BOLT (GRADE 8)* *A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD. V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. FIG. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine. Do not attempt to sharpen while on the mower. 17 CUSTOMER RESPONSIBILITIES TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. OIL DRAIN PLUG ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES AIR SCREEN OIL FILL CAP/DIPSTICK FIG. [. . . ] 36 37 38 39 40 41 42 42A 43 44 45 46 71 790075 790007 799021 786026 792076A 790085 792073 792085A 792075 790025 786066 790086 788069 DESCRIPTION Brake Disc Brake Pad Plate Brake Pad (pkg of 2) Dowel Pin Flat Washer Brake Lever Screw, 1/4-20 x 1-1/4" Screw, 1/4-20 x 2-1/4" Locknut, 5/16-24 Brake Pad Holder Spacer Brake Lever Bracket Square Cut Ring REF PART NO. 71A 792162 79 792144 87 788035 180 730229A 189 792168 189A 792169 190 792150 191 792151 208B 798025 209 798024 DESCRIPTION Pushnut, 9/16" Spring Oil Seal, 5/8" Gear Oil 80W90 Drive Screw #6 x 1/2" Screw, 10-32 x 1/2" Lockwasher Nut, 7/16-20 Fan/Coupling (Incl. 189 & 189A) Control Lever Parts must be ordered from Tecumseh Products Co. inches 1 inch = 25. 4 mm 47 SERVICE NOTES 48 SERVICE NOTES 49 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION SIGHTING GUIDE CUT OUT ON D THIS OTT IS A ED L 15° S INES LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. 50 15° MAX. Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 954140010D




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 954140010D will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.