User manual HUSQVARNA 954140014B

[. . . ] LR122 OWNER'S MANUAL SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. • • • • • • • • • • • • • • • GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. [. . . ] • Withdraw front lift link, rear lift links and mower stabilizer link from brackets. • Slide mower deck out on right side of tractor. MOWER UPSTOP ADJUSTMENT (See Fig. 19) • Raise attachment lift lever to highest (transport) position. • Measure distance from top of mower deck to lower flange of chassis (dim. Remove washer and retainer spring in trunnion, then withdraw trunnion pin from bracket. Loosen trunnion locknut and rotate trunnion counterclockwise on lift link to increase dim. Repeat adjustment if necessary. LOWER FLANGE OF CHASSIS “A” TOP OF MOWER DECK TO INSTALL MOWER (See Fig. 18) • Reverse removal instructions. ENGINE PULLEY MOWER CLUTCH SPRING BELT MOWER CLUTCH ARM AXLE BRACKET RETAINER SPRING WASHER FRONT LIFT TRUNNION RETAINER SPRING WASHER BRACKET TRUNNION LOCKNUT FIG. 19 MOWER STABILIZER LINK REAR LIFT LINKS FRONT LIFT LINK FIG. 18 15 SERVICE AND ADJUSTMENTS TO LEVEL MOWER HOUSING (See Figs. 20-23) Adjust the mower while tractor is parked on level ground or driveway. If tires are over or under inflated, you will not properly adjust your mower. NOTE: One rotation of trunnion nut is equivalent to approximately 1/8 inch of height change. Be sure upper and lower nuts are tightened against trunnion after adjustment has been completed. • Place attachment height adjustment knob in position “3” (See Fig. 21 and 22) • Measure distance from ground to lower flange of mower deck on both sides of mower (dim. • To raise left side of mower, loosen upper trunnion nut and tighten lower trunnion nut. • To lower left side of mower, loosen lower trunnion nut and tighten upper trunnion nut. 22 and 23) To obtain the best cutting results, the mower housing should be adjusted so the rear is approximately 1/4" to 3/ 4" higher than the front when the mower is in height adjustment position “3”. • Measure distance from ground line to lower flange of deck at right front and right rear (dim. “D” & “E”) in line with front and rear tires. Raise or lower rear of mower housing by adjusting the right rear lift link. [. . . ] This proof must include date purchased, model number, serial number, and complete name and address of the selling dealer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. An authorized Husqvarna dealer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area. SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY The following items are not covered by this warranty: (1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tines; (2) Natural discoloration of material due to ultraviolet light; (3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer; (4) Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and (5) Emission Control System components necessary to comply with CARB-95 and EPA regulations which are manufactured by third party engine manufacturer. SECTION 4: EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting from the following: (1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; HUSQVARNA FOREST & GARDEN COMPANY 9006-J PERIMETER WOODS DRIVE CHARLOTTE, NC 28216 531 83 81-23 2/95 SERVICE ® POLICY WARRANTY LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWER TRAIN COMPONENTS A. Products Warranted ® TECUMSEH Issued January 1980 Revised January 1991 TECUMSEH Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below, will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and Series 1100 angle drive and ONE YEAR for all other Peerless products. [. . . ]