User manual HUSQVARNA DUMP CART

[. . . ] 18 Cleaning and Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Preventative Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Caring for Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] • Become familiar with the safe operation of the equipment, operator’s controls, and safety signs. • Never let children or untrained people operate or service the equipment. • The owner/user can prevent and is responsible for accidents or injuries occurring to themselves, other people, and/or property. 2 - Preparation: • Wear appropriate clothing including hard hat, safety glasses and ear protection. • Inspect the area where the equipment is to be used and remove all objects such as rocks, toys and wire which can be thrown by the machine. • Check that operator’s controls, safety switches, hoses, and shields are securely attached and functioning properly. Do not operate unless they are functioning properly. 5 SAFETY RULES 3 - Operation • Never run an engine in an enclosed area. • Only operate in good light, keeping away from holes and hidden hazards. • Do not change the engine governor setting or overspeed the engine. • Stop equipment and inspect vacuum impeller and hoses after striking objects or if an abnormal vibration occurs. • Slow down and use caution when making turns and crossing roads and sidewalks. Install the two (2) strapes with 1/2” bolts and nuts on the hopper and install the two (2) support brackets on the frame. STRAP LANYARD SUPPORT BRACKET FIGURE 3 6. Attach hose support rod to the right side of the unit to keep the right rear tire from rubbing the hose. 11 ASSEMBLY HANDLE ASSEMBLY 1. iZ Models will use the front hole and the LZ Models will use the back hole. When connected adjust the threaded tube using the adjusting nuts at both ends. The adjustment will be complete when the handle is pulled forward and the hopper door is fully closed. 3. 4. HANDLE LZ MODELS HOLES PIVOT PIN iZ MODELS HOLES ROD END TUBE SUPPORT STOP ADJUSTMENT NUT TO HOPPER UNIT BACKING PLATE ADJUSTMENT NUT THREADED TUBE H O P P E R FRAME ROD END 12 ASSEMBLY HOPPER DOOR ADJUSTMENT Adjust door rods on both sides with adjusting nut so door closes evenly. See illustration. HOPPER HOPPER DOOR DOOR ROD ADJUSTMENT NUT DOOR ROD ADJUSTMENT NUT 13 ASSEMBLY Blower/Drive Kit 1. Remove the deck pulley. 2. 3. 4. 5. Note: When the deck pulley is removed, the spindle can fall out of the cutter housing assembly. Be sure to secure the bottom of the spindle so that this does not happen. BLOWER ASSEMBLY PULLEY SHIELD WELDED STUD 3/8” NYLOC NUT 6. Place the double pulley on the cutter housing assembly. Place the heavy washer, and 7/16 lock washer on the 108951, 7/16 x 2 1/2 bolt and install in the spindle. Using the 5/32" allen wrench, remove the 111229, 1/4 x 5/8 screw on the pulley shield. [. . . ] If hoses have excessive wear, tears, or punctures, replace immediately. To prolong the life of the hose, periodically rotate hose and turn hose end to end. Avoid twists and sharp turns in the hoses, as they will increase wear on the hoses. Avoid dragging the lower hose along the sides of buildings or other hard surfaces. Cleaning Poly Mesh The poly mesh on the collection system is located inside the container hood. [. . . ]