User manual HUSQVARNA HAUCT18H42A

[. . . ] CTH180 XP Owner's Manual SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • • • • • • • • • • • • • • • • Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. [. . . ] A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. LUBRICATION CHART ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK ➀ STEERING SECTOR GEAR TEETH ➁ ENGINE BEFORE EACH USE • • • • • Check engine oil level. Check for loose fasteners. ➀ General Purpose Grease ➁ Refer to Maintenance “ENGINE” Section IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. 18 MAINTENANCE TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. 6 STAR PATTERN BLADE W/LEFT HAND THREADED BOLT 5 STAR PATTERN BLADE W/RIGHT HAND THREADED BOLT FIG. 19 5 STAR PATTERN BLADE The center of this blade has a five (5) star pattern. The bolt that attaches this blade has normal Right Hand threads that loosens by turning ( ) counterclockwise and tightens by turning ( ) clockwise. TRAILING EDGE FLAT WASHER BLADE BOLT RIGHT HAND THREADED RH OPERATOR PRESENCE SYSTEM Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the clutch/brake pedal is fully depressed and attachment clutch control is in the disengaged position. • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never operate unless the operator is in the seat. • When the engine is running and the bagger or optional deflector are not installed the mower should not operate. MANDREL ASSEMBLY 5 STAR PATTERN 5 STAR CENTER HOLE LOCK WASHER BLADE FIG. 20 BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. IMPORTANT: THE BLADES ON YOUR MOWER ARE NOT THE SAME AND MUST BE INSTALLED ON THE CORRECT SIDE. IT IS SUGGESTED THAT YOU WORK ON ONE BLADE AT A TIME TO ENSURE PROPER ASSEMBLY OF COMPONENTS. 6 STAR PATTERN BLADE The center of this blade has a 6 star pattern. The bolt attaching this blade has Left Hand threads that loosens by turning ( ) clockwise and tighten by turning ( ) counterclockwise. BLADE FLAT WASHER BLADE BOLT LEFT HAND THREADED 6 STAR PATTERN 6 STAR CENTER HOLE LH MANDREL ASSEMBLY LOCK WASHER TRAILING EDGE FIG. 21 19 MAINTENANCE BLADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove blade bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown. [. . . ] 1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems used for commercial, institutional, professional or income producing purposes or use. This warranty shall be inapplicable to defects resulting from the following: (1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; (2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna; (3)Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or: (4)Additional damage to parts or components due to continued use occurring after any of the above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. [. . . ]