User manual HUSQVARNA HL 1027 STE A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA HL 1027 STE A. We hope that this HUSQVARNA HL 1027 STE A user guide will be useful to you.


HUSQVARNA HL 1027 STE A : Download the complete user guide (1432 Ko)

Manual abstract: user guide HUSQVARNA HL 1027 STE A

Detailed instructions for use are in the User's Guide.

[. . . ] 1027STE Owner's Manual SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Do not operate the equipment without wearing adeLook for this symbol to point out imquate winter outer garments. It means clothing, such as scarves, which can get caught in CAUTION!!! [. . . ] WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the OFF position. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. To avoid possible freeze-up of the starter, proceed as follows: 13 ELECTRIC STARTER 1. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. Disconnect the power cord from the receptacle first, then from the engine. While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times. NOTE: The unusual sound made while pulling the recoil starter handle will not harm the engine or starter. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter. SNOW THROWING TIPS • • • • Always operate the snow thrower with the engine at full throttle. It is easier and more efficient to remove snow immediately after it falls. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. [. . . ] NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 43 44 532 14 63-15 873 80 05-00 532 15 54-15 817 49 05-08 532 18 00-17 532 18 01-34 532 17 92-70 532 18 40-79 532 18 00-82 532 18 00-65 532 18 77-14 532 18 00-66 532 17 88-07 532 18 40-80 532 17 53-44 532 18 78-57 532 17 98-31 532 18 40-78 873 93 05-00 532 17 86-13 874 76 05-14 532 08 51-79 532 18 01-35 532 18 00-81 532 17 86-95 532 17 53-41 532 17 93-52 532 17 53-40 532 18 40-77 532 18 40-76 872 27 05-05 532 17 88-79 532 17 53-23 532 18 40-75 532 18 25-04 532 17 53-48 532 15 53-77 819 11 15-07 810 04 05-00 874 95 05-12 812 00 00-12 532 17 90-95 532 18 42-06 Screw, Hex Head 5/16-18 x 3/4 Nut, Lock 5/16-18 Washer, Flat Screw, Hex Head 5/16-18 x 1/2 Bearing, Flange Shaft, Auxiliary Spacer, Plate Plate, Auxiliary Gear, Intermediate (12/58) Gear, Pinion Rod, Clutch Shaft, Long, Hex Pin, Pivot Lever, Shifter / Wheel Trunnion Bearing Assembly Bracket, Pivot, Shift Ring, Rubber Wheel Plate, Rubber Wheel Nut, Lock 5/16-18 Hub, Rubber Wheel Screw, Hex Head 5/16-18 x 7/8 Retainer, Hairpin Spring, Bias Gear, Axle (58 Teeth) Pin, Pivot Lever Plate Assembly, Drive Shaft, Axle Shaft, Short Hex Lever, Shifter Plate Bracket, Shifter Support Bolt, Carriage 5/16-18 x 5/8 Key, Square 1/4 x 1/4 x 7/8 Bearing, Flange Plate, Drive Mounting Spacer, Bearing Pulley, Traction Drive Nut, Lock 5/16-18 Washer, Flat Washer, Lock 5/16 Screw, Hex Head 5/16-18 x 3/4 Ring, Retaining Spring, Return Pin, Roll NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 27 REPAIR PARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - - MODEL NO. 954 63 35-45 30 3 17 19 6 22 23 28 6 10 21 31 29 41 31 38 41 39 36 37 32 33 34 35 16 42 43 5 11 6 41 44 26 10 21 24 25 26 27 4 2 6 7 18 20 9 1 14 8 13 45 44 12 40 7 6 15 50 52 51 11 49 26 11 53 54 48 11 46 47 28 REPAIR PARTS KEY PART NO. DESCRIPTION CHASSIS / ENGINE / PULLEYS SNOW THROWER - - MODEL NO. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA HL 1027 STE A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA HL 1027 STE A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.