User manual HUSQVARNA LTH 1742 D

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA LTH 1742 D. We hope that this HUSQVARNA LTH 1742 D user guide will be useful to you.


HUSQVARNA LTH 1742 D : Download the complete user guide (1651 Ko)

Manual abstract: user guide HUSQVARNA LTH 1742 D

Detailed instructions for use are in the User's Guide.

[. . . ] 02578_husqvarna 02596 LTH1742 Owner's Manual SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • • • • • • • • • • • • • • • • Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. [. . . ] • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. YELLOW CAP 02463 DRAIN TUBE FIG. 12 • • • • • Unlock drain valve by pushing inward and turning counterclockwise. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. Refill engine with oil through oil fill dipstick tube. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Keep oil at “FULL” line on dipstick. TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized ser vice center/department. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 • CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart1_e FIG. 11 17 MAINTENANCE CLEAN AIR INTAKE/COOLING AREAS To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating. • Place new pre-cleaner and cartridge firmly in base. • Align tabs on cover with slots in blower housing and replace cover. • Hook handle on cover and push down on handle to close. IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. Do not use pressurized air to clean cartridge. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual. AIR FILTER (See Fig. 13) Your engine will not run properly using a dirty air filter. Replace pre-cleaner after every 25 hours of operation or every season. [. . . ] 532 16 58-92 872 14 05-06 532 13 80-17 532 16 54-60 532 12 46-70 532 17 80-24 532 85 08-57 810 03 06-00 532 14 02-96 DESCRIPTION KEY NO. 44 45 46 48 52 53 54 55 56 59 67 68 92 129 130 131 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 184 -- PART NO. 532 14 00-88 532 12 47-88 532 13 77-29 532 13 39-44 532 13 98-88 532 18 49-07 532 17 85-15 532 15 50-46 532 16 57-23 532 14 10-43 532 10 69-32 532 14 49-59 873 80 06-00 819 13 13-12 874 78 06-16 872 14 06-08 532 16 58-90 532 15 71-09 532 15 86-34 532 16 58-88 532 17 19-77 532 13 13-35 532 16 90-22 532 16 58-98 819 09 12-16 532 16 96-70 532 16 96-76 532 16 96-74 532 16 96-75 532 16 96-71 532 16 96-72 532 16 96-69 817 72 04-08 872 14 06-14 819 13 14-10 532 13 07-94 DESCRIPTION 11 --13 14 15 16 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 36 37 40 Deck Asm MWR 42"weldment Bolt Rdhd Sqnk 5/16-18 Unc x 3/4 Bracket Asm Fr Sway Bar 38/42 Bracket Asm Deck 42"sway Bar Retainer Spring Deck Sway Bar Bolt 3/8 - 24 x 1. 25 Gr 8 Washer Lock Hvy 3/8 Washer Hard Blade Mower Vented (The following blades are available) 532 13 41-49 Blade Mower 42" (For mulching mowers only) 532 13 97-75 Blade, 42" Mulching Premium (For better wear when mulching) 532 13 89-71 Blade, 42" Hi-Lift (For bagging or discharging) 532 13 76-45 Shaft Asm W/lower Bearing 532 12 87-74 Housing Mandrel Vented 532 11 04-85 Bearing Ball Mandrel 532 17 44-93 Stripper Mower 872 14 05-05 Bolt Rdhd Sqnk 5/16-18 x 5/8 532 13 28-27 Bolt Shoulder 532 15 97-70 Baffle Vortex 42 873 68 05-00 Nut Crownlock 5/16-18 Unc 532 17 75-63 Bracket Deflector Mower 42" 532 10 53-04 Cap Sleeve 80 x 112 Blk Mower 532 12 37-13 Spring Torsion Deflector 2 52 532 11 04-52 Nut Push Phos & Oil 532 17 18-59 Shield Deflector Mower 42" Blk 819 11 10-16 Washer 11/32 x 5/8 x 16 Ga 532 13 14-91 Rod Hinge 42" 6 75 Wlg 532 17 39-84 Screw Thd Rolling 532 12 99-63 Washer Spacer Mower Vented 532 15 35-35 Pulley Mandrel 42" 532 17 83-42 Nut Toplock Flng 872 11 06-14 Bolt Rdhd 3/8-16 Unc x 1-3/4 Gr. 5 532 13 14-94 Pulley Idler Flat 819 13 13-16 Washer 13/32 x 13/16 x 16 873 68 06-00 Nut Crownlock 3/8-16 Unc Guard Mandrel LH Black Spring Retainer 1" Zinc/cad Screw Hex Thd Cut 1/4-20 x 5/8 T Washer Hardened Smaller Bolt Shoulder 5/16-18 Unc Blkz Arm Asm Pad Brake Washer Hardened Arm Idler 42"mower LT/YT Spacer Retainer Mower Guard TUV Idler Knob Rd 3/8-16 Plstc Thds Blk V-Belt Mower 42" Nut 3/8-16 Unc Washer 13/32 x 13/16 x 12 Ga. Bolt 3/8-16 x 1 Gr. 5 Bolt 3/8-16 x 1 Arm Spring Brake Mower Bracket Arm Idler 42" Keeper Belt 42" Clutch Pulley Idler Flat Bolt Carriage Idler Spring Extension Spring Return Idler Retainer Spring Yellow Washer 9/32 x 3/4 x 16 Ga. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA LTH 1742 D




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA LTH 1742 D will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.