User manual HUSQVARNA LTH 18542 C

[. . . ] 02494 LTH18542 Owner's Manual SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • • • • • • • • • • • • • • • • Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. [. . . ] Tighten oil fill cap/dipstick securely each time you check the oil level. • Remove yellow cap from end of drain valve and install the drain tube onto the fitting. OIL DRAIN VALVE CLOSED AND LOCKED POSITION V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. YELLOW CAP 02463 DRAIN TUBE FIG. 13 • • • • • Unlock drain valve by pushing inward and turning counterclockwise. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Tighten cap onto the tube securely when finished. TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. • SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart1_e FIG. 12 17 MAINTENANCE AIR FILTER Your engine will not run properly using a dirty air filter. See Engine Manual. CLAMP CLAMP ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. FUEL FILTER FIG. 14 MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. CLEANING • Clean engine, battery, seat, finish, etc. • Keep finished surfaces and wheels free of all gasoline, oil, etc. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. [. . . ] 3/8-16 unc Roller Nose Bracket Roller Nose RH Bracket Wheel Gauge LH 42" Deck Bracket Gauge Wheel RH 42" Deck Bolt 5/16-18 Bolt Shoulder Wheel Gauge Nut Centerlock 3/8-16 unc Washer 3/8 x 7/8 x 14 Ga. 3/8-16 x 3/4 Arm Spring Brake Mower Bracket Arm Idler 42" Keeper Belt 42" Clutch Pulley Idler Flat Bolt Carriage Idler Spring Extension Spring Return Idler Retainer Spring Yellow Washer 9/32 x 3/4 x 16 Ga. Clutch Cable 42" Screw Hex Thd Cut 1/4-20 x 1/2 Bolt Rdhd Sqn 3/8-16 unc x 1-3/4 Rod Roller Nose Retainer Spring Washer 13/32 x 7/8 x 10 Ga. Head Asm Cable Clutch Mandrel Assembly(Includes Housing, Shaft and Shaft Hardware Only-Pulley not Included) Replacement Mower, Complete (Std Deck-order separately nose roller and gauge wheel components key nos. [. . . ]