User manual HUSQVARNA PA 1100

[. . . ] Re conta erlyi ently nt prop qu ceme r is g fre pla ine ba d re nta eck de s co Ch mmen n. les r unrioratio reco a INGmowe tie only RNerate and de e Us WA t op wear ged. PA 1100 42 Inch Mower Grass Catcher · · · · · Assembly Operation Customer Responsibilities Service and Adjustments Repair Parts 1 156235 Rev. 4 04. 27. 01 rad Printed in U. S. A. SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. [. . . ] To protect grass catcher cover during assembly place cover upsidedown on overturned carton. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Support Tube (1) Mounting Bracket (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual · NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE GROUP "A" REAR MOUNTING BRACKET AND SUPPORT TUBE TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping (4) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 (2) Wing Nut (1) Support Plate NOT SHOWN FULL SIZE (2) Washer 11/32 x 1-1/2 x 10 Ga. (2) Lock Washer 5/16 GROUP "B" SUPPORT POST TO COVER ASSEMBLY (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 4 BAG OF PARTS CONTENTS (continued) SUPPORT TUBE TO COVER ASSEMBLY GROUP "C" (1) Bolt 5/16 - 18 x 3/4 (1) Bolt 5/16 - 18 x 2-1/4 (1) Bracket Support Pin (2) Locknut 5/16-18 GROUP "D" SUPPORT POST TO MOUNTING BRACKET (1) Retainer Spring (4) Tubing End Caps GROUP "E" (2) Latch Hook Assembly LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. CHUTE LATCH ASSEMBLY to UPPER CHUTE (2) Nut, Weld #10 GROUP "F" (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "G " (1) Rubber Latch CHUTE LATCH ASSEMBLY to LOWER CHUTE (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 5 ASSEMBLY BEFORE YOU START TO ASSEMBLE THE GRASS CATCHER Some tractor models may need minor modifications before you can mount the grass catcher to the tractor. Look carefully at the drawbar on your tractor and compare to the illustrations below. If your drawbar looks like STYLE "A" (has the upper corner ribs), your tractor is ready - proceed with the grass catcher assembly. If your drawbar looks like STYLE "B" (does not have the upper corner ribs), go to the PREPARATION section in this manual. UPPER CORNER RIBS TRACTOR DRAWBAR STYLE "A" TRACTOR DRAWBAR STYLE "B" PARTS IDENTIFICATION UPPER CHUTE COVER er tain on en d. C wh alle placetainer. om r un ioratio rec we ly a NINGmod detier on e te era an Us t WARop wear ged. no Do ject to dama or sub d cke cra is DUMP BAG INDICATOR CHUTE LATCH er tain on en d. C wh alle placetainer. om r un ioratio rec we ly a NINGmod detier on e te era an Us t WARop wear ged. no Do ject to dama or sub d cke cra is er tain on en d. C wh alle placetainer. Install one container to left side first with warning to outside of unit. NOTE: Right container should always overlap left container at center supports. Close cover and lock latch handles over center support tubes. COVER LATCH HANDLES 6 CONTAINER MOUNTING (See Fig. Repeat for other containers. CONTAINER BOTTOM HALF CONTAINER WARNING CONTAINER TOP HALF CONTAINER BOTTOM HALF CENTER SUPPORT TUBES iner nta n . Co whe lled lace er. Use only and WARope age not to wea Do ject or dam sub d cke cra is iner nta n . Co whe lled lace er. Use only and WARope age not to wea Do ject or dam sub d cke cra is PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF LOCKING TAB CONTAINER HANDLE CONTAINER WARNING ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. FIG. Use WA t op wea aged no to m Do ect da or bj su ked crac er tain on hen d. C w r. R t co erly ently en prop qu acem r is g fre pl ne ba d re ntai ck de co Che men less tion. Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw, washer, and lock washer nut as shown. With your right hand, raise and hold deflector shield in upright position. [. . . ] · Place gearshift/motion control lever in neutral (N) position. · Make sure blades and all moving parts have completely stopped. · Disconnect spark plug wire(s) from spark plug(s) and place wire where it cannot come in contact with plug. CAUTION: Do not leave grass in bagger containers. Failure to do so may result in spontaneous combustion which could develop into a fire. CAUTION: Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. [. . . ]