User manual HUSQVARNA QD92I

[. . . ] Never store the equipment with petrol in the tank inside a building where fumes can reach an open flame or spark. To reduce the fire hazard, keep the engine, silencer, battery compartment and petrol storage area free of vegetative material and excessive grease. These symbols may appear on your machine or in the literature supplied with the product. Gearcase notch Handle lock Handle (high position) Shift lever Handle (low position) Handle lock lever Getriebegehäuse-Aussparung Handgriffsperre Handgriff (obere Stellung) Schalthebel Handgriff (untere Stellung) Hangriffsperrenhebel Insert one handle lock (with teeth facing outward) in gearcase notch (fig. [. . . ] Insert second handle lock (with teeth facing inward) in slot handle base (fig. With handle assembly in lowest position, securely tighten handle lock lever by rotating clockwise. Shift rod Hairpin clip Shift lever indicator Handle assembly Carriage bolt and locknut Handle base Slot Greasecase Handle lock Washer Handle lock lever Pivot bolt Schaltstange Haarnadelklemme Schalthebelanzeiger Handgriffmontagesatz Wagenbolzen und Kontermutter Handgriffplatte Schlitz Getriebegehäuse Handgriffsperre Unterlegscheibe Handgriffsperrenhebel Gelenkbolzen Connect shift rod a. Tire pressure Reduce tire pressure to 20 PSI (Tires were overinflated for shipping purposes). Before operating your tiller for the first time, study this section and the "1. Check engine oil level With engine level, remove engine oil filler plug (fig. Be very careful not to allow dirt to enter the Engine when checking or adding oil or fuel. Use clean 30 or 10W-30 grade oil and store in approved, clean covered containers. (Do not use pressurized starting fluid, as severe internal engine damage may occur due to loss of lubrication. Starting the engine Starter handle Choke lever Spark plug wire Fuel Valve Shift lever indicator Drive control lever "disengaged" position Drive control lever "engaged" position Drive control release "unlocked" position Drive control release "locked" position Throttle control Handle grip Reconnect spark plug wire (fig. Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Hard soil should be moistened before tilling: however, extremely wet soil will "ball-up" or clump during tilling. For easier handling of your tiller, leave about 8 inches of untilled soil between the first and second tilling passes. To get through a really tough section of sod or hard ground, apply upward pressure on handle or lower the depth stake. Cultivating is destroying the weeds between rows to prevent them from robbing nourishment and moisture from the plants. Cultivate up and down the rows at a speed which will alow tines to uproot weeds and leave the ground in rough condition, promoting no ruther growth of weeds and grass (fig. Disconnect spark plug wire and cover before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Once a season, lubricate the right hand gear case grease fitting with 1 oz. To avoid the formation of gum deposits in the fuel system it should be drained if the machine is not to be used for 30 days or longer. Remove spark plug, pour one half ounce of clean engine oil into cylinder. Clean entire tiller, especially cylinder fins, blower housing and air screen. Gasoline stored for several months will lose it's volatility (ability to burn effectively); therefore, always use up gasoline at the end of the season. [. . . ] Do not store, spill or use gasoline near an open flame or devices such as a stove, furnace or water heater which utilize a pilot light, or devices that can create a spark. First 2 hours Before each use Every 5 hours Every 25 hours Every 50 hours Check engine oil level Change engine oil Oil pivot points Spark arrester muffler Inspect air screen Air cleaner Clean engine cylinder fins Replace spark plugs Handle can be positioned at different settings between "high" and "low" positions (fig. Stop the engine and remove the spark plug wire and cover from the spark plug (fig. A badly worn tine causes your tiller to work harder and dig shallower. [. . . ]