User manual HUSQVARNA T30356

[. . . ] T30356 36 Inch Mower Grass Catcher Assembly Operation Customer Responsibilities Service and Adjustments Repair Parts 140600 954 04 02-82 1 07. 10. 00 Rev. 3 rad Printed in U. S. A. SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION · · · · · · · · · · · · · · · · Read, understand, and follow all instructions in the manual and on the machine before starting. [. . . ] Always wear safety glasses or eye shields before starting your tractor and while mowing. We recommend wide vision safety mask for over the spectacles or standard safety glasses. UNPACKING INSTRUCTIONS · · Remove all parts and packing materials from carton. Fold flaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. Be sure all parts are there. CARTON CONTENTS: (2) Container Tops (2) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Mounting Bracket (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual (2) Wheel Weights · NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION LATCH HOOK ATTACHMENT TO MOWER DECK REAR MOUNTING BRACKET TO DRAW BAR HARDWARE SHOWN ACTUAL SIZE GROUP "A" (2) Bolt 5/16 - 18 x 1 (2) Locknut 5/16-18 (2) Nut, Acorn 5/16-18 GROUP "B" (4) Shoulder Bolt, Self-Tapping GROUP "C" SUPPORT POST TO CORNER SUPPORT (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 GROUP "D" SUPPORT POST TO MOUNTING BRACKET (1) Bracket Support Pin (1) Retainer Spring (3) Tubing End Caps 4 BAG OF PARTS CONTENTS (continued) GROUP "E" (2) Latch Hook Assembly LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Nut, Weld #10 GROUP "F" CHUTE LATCH ASSEMBLY to UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "G" (1) Rubber Latch CHUTE LATCH ASSEMBLY to LOWER CHUTE (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 GROUP "H" WHEEL WEIGHTS TO FRONT WHEELS **ITEMS NOT SHOWN FULL SIZE** (2) "U" Bolt (4 ) Locknut 5 ASSEMBLY BEFORE YOU START TO ASSEMBLE THE GRASS CATCHER Some mower models may need minor modifications before you can mount the grass catcher to the unit. Look carefully at the mower deck on your unit and compare the deck mandrel to the illustrations below. If your mower deck mandrel looks like STYLE "A", your unit is ready - proceed with the grass catcher assembly. If your mower deck mandrel looks like STYLE "B", go to the PREPARATION section in this manual. DECK MANDREL STYLE "A" DECK MANDREL STYLE "B" PARTS IDENTIFICATION COVER UPPER CHUTE WHEEL WEIGHT U-BOLT DUMP BAG INDICATOR r is taine . Con en led ce wh r. t co pe ently en pro qu em r is g frereplac ine ba nta eck nded s co Ch les ion. 8A COVER LATCH HANDLE CONTAINER WARNING AD INR n o s to GtNepo tcejbuc r r e a ot ca o m ew dek re w a ra d ro lnu dn a se ed a m c s eit e g n o t a r oi r s U . a yl n e rp p o k c o c er lr e a b si y rf g m m tsn uqe dne ell a lt n e r d e C. d . y pe n o l p e R e c al i at en eca e m si r e h w o c t n n i at n . ren W DEFLECTOR SHIELD LATCH HOOKS AD INR n o s to GtNepo tcejbuc r r e a ot ca om ew dek rew na ra d ro a d lnu se eited egam cs no taroir sU . d iat en noi o e si r C . yln rp kceh er a po oc lre ab siy rf g mm tsn uqe dne ella ltne r de C. d R . y alpe no iat calpeemec en si r hw e oc tn ne iatn ren CONTAINER HANDLE CENTER SUPPORT TUBE FIG. erlyi ly ent cont prop uent freq cem r is aineck bag repla nded contChe ss mme unle tion. wea not Do ect to dam or subjked crac r is tainen Con whe r lled. lace aine s nstaRep . erlyiently ent cont prop frequ cem r is aineck bag repla nded contChe ss mme tion. Use oper r wea aged not Do ect to dam or subjked crac CONTAINER WARNING 9 · · · CHUTE LATCH ASSEMBLY (See Fig. Press weld nut into rubber latch and assemble rubber latch to lower chute, as shown. SPLIT SPACER 8 · · · · · · LOWER CHUTE (See Figs. 8A & 8B) Use Hardware - - GROUP "E" #10 X 1-1/8" SCREW Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw, washer, and lock washer as shown. Place front of chute over front of mower deck opening and slide into place, as shown. [. . . ] · Clean unit thoroughly after each use. STORAGE When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. BLADE CARE For best results mower blades must be kept sharp. · See BLADE CARE instructions in your tractor owner's manual. CAUTION: BEFORE PERFORMING ANY MAINTENANCE, SERVICE OR ADJUSTMENTS: · Depress clutch brake pedal fully and set parking brake. [. . . ]