User manual HUSQVARNA YTH22V42LS

[. . . ] 07002 YTH22V42LS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 43 86-83 Rev. 8 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. [. . . ] • Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY. • Install and tighten blade bolt securely (45-55 Ft. torque). MANDREL ASSEMBLY BLADE IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED. BLADE BOLT (SPECIAL) STAR CENTER HOLE Fig. 14 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. NOTE: The original equipment battery on your tractor is maintenance free. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Clean terminals and battery cable ends with wire brush until bright. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 15 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 13 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. TO CHANGE ENGINE OIL (See Fig. CAUTION: Remove lower dash cover carefully to ensure cover tabs are not broken. • Slide lower dash cover up to release cover tabs from tapered slots in lower dash and remove. LOWER DASH COVER TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. TABS SLOTS ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 02 46 3 Fig. Slide oil drain extension from the docking position on the engine blower housing and extend outward from engine. DOCKING POSITION OIL DRAIN EXTENSION TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE CAP NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, they will result in increased oil consumption when used above 32°F (0°C). [. . . ] Washer, Lock Hvy Hlcl Spr 3/8 Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Adapter, Wheel Steering Steering Support Lower Insert, Wheel Steering Screw 3/8-16 x 3/4 Gear, Sector Plate Washer 9/16 ID x 2-3/8 OD 12 Ga. DESCRIPTION 51 873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf 53 532 18 89-67 Washer Hardened . 793 x 1. 637 x . 060 54 874 76 06-36 Bolt Hex 3/8-16 unc x 2-1/4 55 532 41 47-36 Spacer Brace Axle 58 532 19 47-47 Bolt Shoulder Sector Pivot CFM 59 532 19 47-48 Washer Thrust Sector Steering 60 873 97 10-00 Nut Flange Lock 5/8-11 61 532 19 47-40 Draglink, LH 62 532 19 47-41 Draglink, RH 63 817 00 05-12 Screw 5/16-18 x 3/4 64 532 19 98-49 Retainer Clip Spring Steering 65 532 19 47-34 Brace Axle Front 66 871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr 67 532 19 47-37 Bushing PM Front Axle 68 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5 69 532 19 91-62 Washer 1. 5 x . 505 x . 118 70 532 19 61-97 Bracket Deck Susp. Front 78 532 05 70-79 Washer Thrust NOTE: All component dimensions given in U. S. [. . . ]