User manual ICOM CS-F3 PROGRAMMING MANUAL

[. . . ] r Type the setup program name with full path name, then press the [Enter] key. If the serial number on the CD is "000001, " enter "002379-000001" as the ID number. u Program group `CS-F3' appears in the `Programs' folder of the start menu. s CONNECTION Connect each item as in the following diagram. CAUTION: Do not connect an antenna to the transceiver during cloning operation. [. . . ] However, time-out timer must be activated due to local regulation in some countries. The time period is programmed in the TOT-- TOT Timer in 3-3 COMMON 1 (p. Go to TOT-- TOT Timer Go to CH Atr The power save start times are programmed in the PWR Save-- Start Timer (1st), (2nd) in 3-5 EXPERT (p. Go to PWR Save-- Start Timer (1st), (2nd) Go to CH Atr 28 MEMORY CHANNEL-- PMR 5 · CH Atr Selects the channel attribution from Prio A, Prio B, Emergency, Emergency OFF and SmarTrunk ON/OFF. Right click on the desired channel to open the submenu window as at right, then select the channel attribution. SmarTrunk specified bank/s, the bank item in the Memory Channel folder, displayed in the Tree View Screen, changes from regular to SmarTrunk type as follows, for easy recognition. : Regular type : SmarTrunk type [Priority A], [Priority A (Rewrite)], [Priority B], [Emergency Single] and [Emergency Repeat] switches are assigned in 3-1 KEY & DISPLAY ASSIGN (pgs. The man down function is specified in Man Down-- ON, Timer in 3-4 COMMON 2 (p. Go to w Memory Channel Go to Prio A, Prio B A: Priority-- "A" tagged channel becomes the priority channel A, simply recalled by pushing [Priority A] or [Priority A (Rewrite)] switch, and also is automatically monitored during the priority scan. When [Priority A (Rewrite)] switch is assigned, priority channel A can be re-assigned by pushing [Priority A (Rewrite)] switch for 1 sec. B: Priority-- "B" tagged channel becomes the priority channel B, simply recalled by pushing [Priority B] switch. E: Emergency-- "E" tagged channel becomes an emergency channel, immediately recalled and sends an emergency signal by pushing [Emergency Single] or [Emergency Repeat] switch, or when the man down function is activated. Both CTCSS/DTCS and noise squelch mutes are released (audio is emitted) while pushing and holding [Moni(Audi)] switch when 5-tone mute is released or `CONT' is selected in CH Mute (p. 38) in this screen. · SW Action-- Moni-- continued In A : Mutes the 5-tones when `SGL' is selected in CH Mute (p. Both CTCSS/DTCS and noise squelch mutes are released (audio is emitted) while pushing and holding [Moni(Audi)] switch while 5-tone mute is activated. In A+R1, In A+R2: In addition to the `In_A' condition as above, a reset code 1 or 2 is automatically transmitted when call transmission is performed or 5-tone mute is activated by pushing [Moni(Audi)] switch. Both : Mutes the 5-tones when `SGL' is selected in CH Mute (p. Releases all mute controls and emits audio while pushing and holding [Moni(Audi)] switch. 32 SCREEN MENU OPERATION-- PMR 5 · SW Action-- Moni (continued) Both+R1, Both+R2: In addition to the `Both' condition as above, a reset code 1 or 2 is automatically transmitted when call transmission is performed via [Call] switch or 5-tone mute is activated by pushing [Moni(Audi)] switch. The [Moni(Audi)] and [Call] switches are assigned in the 3-1 KEY & DISPLAY ASSIGN (pgs. 52), and channels 32 (reset code 1) and 31 (reset code 2) are used, respectively. The mute condition will be returned to initial condition when the Auto Reset timer is activated, specified in Auto Reset in this screen (p. Go to CH Mute Go to Moni(Audi) Go to Call Go to 10-2 TX CODE CHANNEL Go to Auto Reset · SW Action-- Sel Selects the mute condition after memory or TX code channel selection from OFF, Aud and In A. Aud : Releases the 5-tone mute when `SGL' is selected in CH Mute (p. The mute condition will be returned to initial condition when the Auto Reset timer is activated, specified in Auto Reset in this screen (p. Go to CH Mute Go to Auto Reset 33 5 SCREEN MENU OPERATION-- PMR · SW Action-- Call, PTT Selects the mute condition after [Call] and [PTT] switches action from Aud and OFF. [. . . ] · TX ID, RX ID Enter a 3-digit ID code for both transmit and receive. · Scan Selects automatic scanning capability from Yes and No. · Inter-connect Selects inter-connect capability from Yes and No. · Selective Call Selects selective calling capability from Yes and No. · ANI Selects ANI (Automatic Numbering Identification) transmission capability from Yes and No. *All the other programming operation methods are the same as CS-F3. 63 13 DATA CLONING BETWEEN TRANSCEIVERS s This operation is useful when cloning transceiver(s) with exactly the same setting, without a PC and programming software. s REQUIRED EQUIPMENT The following hardware is required: · Two OPC-966 CLONING CABLES · DB25 Male-Male cross cable (purchase locally) s CONNECTION Connect each item as illustrated in the diagram at right. CAUTION: Do not connect an antenna to the transceiver during cloning operation. [. . . ]