User manual ICOM IC-756PROII

[. . . ] INSTRUCTION MANUAL HF/50 MHz ALL MODE TRANSCEIVER i756PROTM This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. EXPLICIT DEFINITIONS WORD R WARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk or personal injury, fire or electric shock. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating instructions for the IC-756PROII. PRECAUTIONS R WARNING HIGH VOLTAGE! [. . . ] For your information When an external keypad is connected to the pin 3 and pin 7 of the [MIC] connecter, the recorded message, T1­T4, can be transmitted without opening the voice recorder set screen. See page 73 for details. CQ J A 3 Y U A C Q JA3YUA 10s 10s ------------50% T1 T2 T3 T4 DEF e Push the desired memory channel switch, [(F-1)T1] ­ [(F-4)T4], momentarily to transmit the contents. r Rotate the tuning dial to adjust the transmit voice level. · Push [(F-5)DEF] to select the default condition. AGC MID VOX OFF COMP OFF WIDE T1 T2 T3 VOICE RECORDER SEND T1 T1 T2 T2 T3 T3 T4 T4 CQ J A 3 Y U A C Q JA3YUA 10s 10s ------------TX_LEVEL TX LEVEL 50% T4 DEF t Push [EXIT/SET] to return to the voice recorder screen. 41 5 RECEIVE AND TRANSMIT I RTTY decoder The transceiver has an RTTY decoder for Baudot (mark freq. : 2125 Hz, shift freq. : 170 Hz, 45 bps). An external terminal unit (TU) or terminal node controller (TNC) is not necessary for receiving a Baudot signal. q Push [EXIT/SET] several times to close a multifunction screen, if necessary. e Push [(F-3)DECODE] to turn the RTTY decoder ON. · RTTY decoder screen appears. AGC MID RTTY FIL ON u Push [(F-2)CLR] for 1 sec. i Push [EXIT/SET] to exit the RTTY decoder screen. · Setting the decoder threshold level Adjust the RTTY decoder threshold level if some characters are displayed when no signal is received. e Rotate the tuning dial to adjust the RTTY decoder threshold level. · Push [(F-3)DEF] to select the default condition. AGC MID RTTY FIL ON RTTY DECODE **** RTTY Decode Monitor **** **** RTTY Decode Monitor **** 45bps BAUDOT Mark=2125, Shift=170 45bps BAUDOT Mark=2125, Shift=170 UnShift On Space support (SET-OTHERS) UnShift On Space support (SET-OTHERS) New Line Code selectable (SET-OTHERS) New Line Code selectable (SET-OTHERS) If RTTY-FIL is OFF, Please turn ON. -------------------------------------------THRESHOLD 9 RTTY DECODE 1/4 OFF HOLD CLR ADJ WIDE **** RTTY Decode Monitor **** **** RTTY Decode Monitor **** 45bps BAUDOT Mark=2125, Shift=170 45bps BAUDOT Mark=2125, Shift=170 UnShift On Space support (SET-OTHERS) UnShift On Space support (SET-OTHERS) New Line Code selectable (SET-OTHERS) New Line Code selectable (SET-OTHERS) If RTTY-FIL is OFF, Please turn ON. -------------------------------------------ADJ THRESHOLD 9 r If the RTTY filter is turned OFF, push [RTTY FIL] to turn the function ON. · The RTTY decoder does not function when the RTTY filter is turned OFF. 1/4 OFF DEF ADJ WIDE r Push [EXIT/SET] to exit the RTTY decoder screen. The UnShift On Space (USOS) function and new line code can be set in the miscellaneous (others) set mode. 71) t Push [(F-1)HOLD] to freeze the current screen. · "HOLD" appears while the function is in use. y Push [(F-5)WIDE] to toggle the normal or wide screen space. ANT 1 BW 350 TX SFT 0 RTTY RTTY qw:pp FIL2 FIL FIL2 FIL V F O qrqotpp VFO 14. 100. 00 METER Po P. AMP 1 ATT OFF RTTY DECODE AGC MID RTTY FIL ON **** RTTY Decode Monitor **** **** RTTY Decode Monitor **** 45bps BAUDOT Mark=2125, Shift=170 45bps BAUDOT Mark=2125, Shift=170 UnShift On Space support (SET-OTHERS) UnShift On Space support (SET-OTHERS) New Line Code selectable (SET-OTHERS) New Line Code selectable (SET-OTHERS) If RTTY-FIL is OFF, Please turn ON. -------------------------------------------CQ CQ CQ THIS IS JA3YUA JA3YUA OSAKA JAPAN CQ CQ CQ THIS IS JA3YUA JA3YUA OSAKA JAPAN CQ CQ CQ THIS IS JA3YUA JA3YUA OSAKA JAPAN 1/4 OFF HOLD CLR THRESHOLD 9 ADJ WIDE I RTTY tuning meter The transceiver has an RTTY tuning indicator to be tuned correctly and easily. The RTTY tuning meter is automatically displayed when the RTTY filter is turned ON. w Push [RTTY FIL] to activate the RTTY filter and RTTY tuning meter. ANT 1 RTTY tuning meter BW 350 SFT 0 FIL2 qw:pp TX TX METER Po P. AMP 1 ATT OFF VFO RTTY qr. qot. pp 1 14. 100. 00 USB VFO USB FIL2 qr. wpt. pp 1 14. 100. 00 USB 42 RECEIVE AND TRANSMIT 5 I Electronic CW keyer The transceiver has an electronic keyer. Keying weight, the ratio of dot : space : dash, can be set from 1 : 1 : 2. 8 to 1 : 1 : 4. 5 in keyer set mode. o Push [(F-2)] to select the "Rise Time" item. AGC MID BK-IN OFF KEYER CW-KEY K e y e r R e p e a t T i m e t D o t / D a s h R a t i o h Rise Time P a d d l e P o l a r i t y P Keyer Type M I C U p / D o w n K e y e r n 2s 1:1:3. 0 4ms Normal ELEC-KEY OFF · Setting the electronic keyer q Push [EXIT/SET] several times, if necessary. w Push [CW/RTTY] to select CW mode. 1/4 OFF é è DEF !0 Rotate the tuning dial to select the time which the output power becomes the set transmit power. !1 Push [(F-2)] to select the "Paddle Polarity" item. AGC MID BK-IN OFF KEYER CW-KEY K e y e r R e p e a t T i m e t D o t / D a s h R a t i o h Rise Time P a d d l e P o l a r i t y P Keyer Type M I C U p / D o w n K e y e r n 2s 1:1:3. 0 4ms Normal ELEC-KEY OFF [CW/RTTY] switch [KEYER] switch 1/4 OFF é e Push [KEYER] then [EXIT/SET] to select keyer set mode. ANT 1 è DEF BW 500 SFT 0 CW FIL2 BPF qw:pp TX TX METER Po P. AMP 1 ATT OFF VFO qr. qot. pp 1 14. 100. 00 USB VFO CW FIL2 qr. wpt. pp 1 14. 100. 00 MEMORY KEYER MEMORY KEYER MENU SEND Max. 55 Characters x 4ch SEND Max. 55 Characters 4ch !2 Rotate the tuning dial to select the paddle polarity between normal and reverse polarity. !4 Rotate the tuning dial to set the electronic keyer function to electronic keyer, bug-key or straight key (electronic keyer OFF). · Bug-key setting can be substituted for a bug-key while operating with a paddle. Set to "Straight" for a real bugkey, or connect the bug-key to [KEY] on the rear panel. AGC MID BK-IN OFF KEYER CW-KEY K e y e r R e p e a t T i m e t D o t / D a s h R a t i o h Rise Time P a d d l e P o l a r i t y P Keyer Type M I C U p / D o w n K e y e r n 2s 1:1:3. 0 4ms Normal ELEC-KEY OFF USB AGC MID BK-IN OFF EDIT Memory Editor EDIT Memory Editor 001 001 Style Contest Number 001 001 Style Contest Number 1/4 OFF SEND CW KEY Memo-key, Elec-key, CW Wave Form Set CW KEY Memo-key, Elec-key, CW Wave Form Set EDIT 001 CW KEY r Push [(F-4)CW KEY] to select memory keyer set mode. t Select the "Keyer Repeat Time" item using [(F1)]. AGC MID BK-IN OFF KEYER CW-KEY K e y e r R e peat T i m e r p e a t Time D o t / D a s h R a t i o h Ratio R i s e T i m e e P a d d l e P olarity e olarity K e y e r T y pe r pe M I C U p / D own K e y e r U o w n Keyer 2s 2s 1:1:3. 0 1:1:3. 0 4ms 4ms Normal Normal ELEC-KEY ELEC-KEY OFF OFF 1/4 OFF é è DEF !5 Push [(F-2)] to select the "MIC Up/Down Keyer" item. [. . . ] Specially designed to tune a long wire antenna for portable or mobile HF operation. The PTT tuner start function provides simple operation. · Input power rating: 120 W · Frequency coverage: 7­54 MHz bands with the AH-4 Unidirectional, electret microphone for base station operation. Includes [UP]/[DOWN] switches and a low cut function. HM-36 HAND MICROPHONE Hand microphone equipped [UP]/[DOWN] switches. SP-21 EXTERNAL SPEAKER CT-17 CI-V LEVEL CONVERTER with UT-102 VOICE SYNTHESIZER UNIT Announces the receive frequency, mode and S-meter level in a clear, electronically-generated voice, in English (or Japanese). SP-20 EXTERNAL SPEAKER 4 audio filters; headphone jack; can connect to 2 transceivers. [. . . ]