User manual ICOM IC-910H

[. . . ] INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER i910H IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. EXPLICIT DEFINITIONS WORD R WARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating instructions for the IC-910H. PRECAUTIONS R WARNING HIGH VOLTAGE!NEVER attach an antenna or internal antenna connector during transmission. [. . . ] u Push [TRANSMIT] to return to receive mode. [TRANSMIT] [M/S·BAND] [SSB/CW] r Rotate the tuning dial to set the operating frequency. t Push [TRANSMIT] to set the transceiver to transmit mode. 38 · The MAIN band indicator lights red. Tuning dial RECEIVE AND TRANSMIT 5 D Setting keying speed q Push [SET] then [SSB/CW] to enter the SSB/CW set mode. w Push [DN M] or [L UP] to select the keying speed item. · "SPEEd" is displayed. D Setting side tone q Push [SET] then [SSB/CW] to enter the SSB/CW set mode. w Push [DN M] or [L UP] to select the side tone item. · "SidE-t" is displayed. e Rotate the tuning dial to adjust the keying speed to the desired speed. · Keying speed can be selected from 6­60 wpm. to return to the default value. e Rotate the tuning dial to adjust the side tone level to the desired level. · Push [M-CL 5] for 1 sec. to return to the default value. r Push [SSB/CW] to exit the SSB/CW set mode. r Push [SSB/CW] to exit the SSB/CW set mode. D Setting semi break-in function q Push [SET] then [SSB/CW] to enter the SSB/CW set mode. w Push [DN M] or [L UP] to select the semi break-in item. · "br-In" is displayed. e Rotate the tuning dial to turn the semi break-in function ON and OFF. · Push [M-CL 5] for 1 sec. to return to the default setting. r Push [DN M] or [L UP] to select the delay time item. · "dELAy" is displayed. t Rotate the tuning dial to set the delay time to the desired time period. · Delay time can be selected from 2. 0­13. 0 sec. to return to the default value. y Push [SSB/CW] to exit the SSB/CW set mode. D Setting keying weight q Push [SET] then [SSB/CW] to enter the SSB/CW set mode. w Push [DN M] or [L UP] to select the keying weight item. · "rAtio" is displayed. e Rotate the tuning dial to adjust the keying weight ratio to the desired level. · Keying weight ratio can be selected from 1:1:2. 8 to 1:1:4. 5. to return to the default value. r Push [SSB/CW] to exit the SSB/CW set mode. KEYING WEIGHT EXAMPLE: Morse code "K" DOT (Fixed*) D Setting CW pitch q Push [SET] then [SSB/CW] to enter the SSB/CW set mode. w Push [DN M] or [L UP] to select the CW pitch item. · "Pitch" is displayed. Weight setting: 1:1:3 (default) Weight setting: Adjusted DASH DASH e Rotate the tuning dial to adjust the CW pitch to the desired pitch. · CW pitch can be adjusted within 300­900 Hz range. to return to the default value. Adjustable range SPACE (Fixed*) r Push [SSB/CW] to exit the SSB/CW set mode. *SPACE and DOT length can be adjusted with the keying speed only. 39 6 MEMORY OPERATION Memory Channel 1­99 I Memory channels The IC-910H has 106 memory channels (99 for regular, 6 scan edges and 1 call) and they are equipped for each frequency band for storing the most often used frequencies and operating mode, as well as tone frequency, offset frequency, etc. Description Regular memory channels. Programs operating frequency, mode, subaudible tone activity with frequency and split/duplex conditions. Programs operating frequency, mode, etc. , and is available for each band, independently. 1A/1b­3A/3b C I Operation on a memory channel Frequency and mode, etc. , can be changed in a memory channel. However, they will be cleared if [MW 4] is not pushed. D Memory channel selection q Push [V/M 1] to select memory channel mode. · "MEMO" indicator appears. [DN ] [UP ] w Push [DN M] or [L UP] to select the desired memory channel. · Memory channel changes continuously while holding [DN M] or [L UP]. · The tuning dial rotation while pushing [F-INP ENT] also selects memory channel. FM VFO A Select memory mode FM MEMO e Push [V/M 1] to return to VFO mode. D During VFO mode operation By pushing [DN M] or [L UP] during VFO mode operation, memory channel is also selectable. However, the frequency readout does not change in this case, only the memory channel number changes. Select memory channel USB MEMO 40 MEMORY OPERATION 6 I Programming in VFO mode Memory channel programming can be performed either in VFO mode or in memory mode. q Set the desired operating frequency and mode in VFO mode. · Push [V/M 1] to select VFO mode, if required. · Tone frequency, offset frequency, etc. , can also be programmed. [. . . ] 500 Hz/­6 dB Hand microphone equipped with [UP]/[DOWN] switches. Same as that supplied with the transceiver. SP-21 EXTERNAL SPEAKER SM-20 DESKTOP MICROPHONE UT-106 DSP UNIT Designed for base station operation. input power: 5 W Unidirectional, electret microphone for base station operation. Includes [UP] and [DOWN] switches and a low cut function. Allows AF DSP capabilities, including noise reduction and auto notch filter. UX-910 1200 MHz BAND UNIT MB-23 CARRYING HANDLE CT-17 CI-V LEVEL CONVERTER Allows you additional all mode operation on the 1200 MHz band. Carrying handle, portable operation. convenient for For remote transceiver control using a personal computer. [. . . ]