User manual ICOM IC-E7

[. . . ] INSTRUCTION MANUAL VHF/UHF DUAL BAND FM TRANSCEIVER iE7 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-E7 VHF/UHF DUAL BAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] · If "OFF" appears, check the offset frequency (see p. qSet the receive frequency, or shift direction (see p. 19 for details. ). to transmit a 1750 Hz tone burst signal. · The displayed frequency automatically changes to the transmit frequency (repeater input frequency). · If "OFF" appears, check the offset frequency (see p. 20 for details) or shift direction (p. 19). then SCAN SCAN S. MW S. MW SET SET SET rPush and hold [PTT] to transmit. yPush and hold [SQL] (ATT·SET) to monitor the repeater input frequency. ePush and hold [PTT] to transmit. tPush and hold [SQL] (ATT·SET) to monitor the repeater input frequency. 23 MEMORY/CALL CHANNELS General description The IC-E7 has 1050 memory channels including 50 scan edge memory channels (25 pairs) for storage of often-used frequencies. And a total of 18 memory banks, A to H, J, L, N, O to R, T, U and Y are available for storing groups of frequencies, etc. Up to 100 channels can be assigned into a bank. 6 Memory channel programming q Push [V/M] (SKIP·S. MW) to select VFO mode. w Set the desired frequency: Select the desired band with [BAND] (TS·LOCK). offset frequency, duplex direction, subaudible tone frequency, etc. ), if desired. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. D Memory channel contents The following information can be programmed into memory channels: · Operating frequency (p. 14) · Duplex direction (DUP or ­DUP) with an offset frequency (pgs. 39). 5 6 r Rotate [DIAL] to select the desired channel. · Call channels (C0, C1), VFO (VF) and scan edge channels (00A/00b to 24A/24b), as well as regular memory channels, can be programmed in this way. · While pushing and holding [FUNC], rotate [DIAL] to select memory channel in 10 channel steps. t Push and hold [V/M] (SKIP·S. MW) for 1 sec. · 3 beeps sound · Memory channel number automatically increases when continuing to push [V/M] (SKIP·S. MW) after programming. [EXAMPLE]: Programming 439. 370 MHz into memory channel 20 (blank channel). Push WFMAM -DUP T SQL S. MW for 1 sec. WFMAM -DUP T SQL Rotate DTCS ATT WFMAM -DUP T SQL Push DTCS ATT S. MW for 1 sec. WFMAM -DUP T SQL DTCS ATT DTCS ATT WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 24 6 MEMORY/CALL CHANNELS Memory bank setting The IC-E7 has a total of 18 banks (A to H, J, L, N, O to R, T, U and Y). Regular memory channels, 000 to 999, may assigned into a desired bank for easy memory management. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. rWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank. · Banks A to H, J, L, N, O to R, T, U and Y are available. · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with WFMAM -DUP T SQL + w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. " · After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. [. . . ] Tuning step selection While pushing and holding [FUNC], push [BAND] to enter tuning step selection. Then rotate [DIAL] to select the desired tuning step. · Push [BAND] again to return to the previous condition. Frequency setting q Push [V/M] to select VFO mode. w Rotate [DIAL] to set the desired operating frequency. · While pushing [FUNC], dial rotation changes frequency in 1 MHz steps. 1750 Hz tone burst Push [PTT] briefly, then push and hold [PTT] again for 1 to 2 sec. Set mode setting q While pushing and holding [FUNC], push and hold [SQL] for 1 sec. [. . . ]