User manual ICOM IC-F2010

[. . . ] NEVER expose the transceiver to rain, snow or any liquids. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other countries. SmarTrunk IITM is a Trademark of SmarTrunk Systems, Inc. USE supplied microphone only. Other microphones have different pin assignments and may damage the transceiver. DO NOT use or place the transceiver in areas with tem- i TABLE OF CONTENTS peratures below ­25°C or above +55°C or, in areas subject to direct sunlight, such as the dashboard. IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] o ALPHANUMERIC DISPLAY Displays the CH number, 5-tone indication, DTMF numbers, Audible indication, etc. I Programmable function keys The following functions can be assigned to [P0], [P1], [P2], [P3], [P4], [], [], [ ] and [ ] programmable function keys. Consult your Icom Dealer or System operator for details concerning your transceivers programming. In the following explanations, programmable function names are bracketed, the specific switch used to activate the function depends on programming. [CH UP] [CH DN] CH UP AND DOWN KEYS · Select an operating channel. · Select a transmit code channel after pushing the [TX CH] key. OPERATING CHANNEL KEYS Select an operating channel directly. [CH1] [CH2] [CH3] [CH4] [PRI A] [PRI B] 3 PRIORITY CHANNEL KEYS Select priority A or priority B channel with each push. PANEL DESCRIPTION [BANK] BANK KEY Select and determine a bank number. · When the optional UT-105 is installed, push [BANK] then push [CH UP]/[CH DN] to select operating bank number, and then push [BANK] to determine the bank number. 1 [MONI] MONITOR KEY Activates one of (or two of) the following functions on each channel independently: · Push and hold the key to unmute the channel (audio is emitted; `Audible' condition). · Push the key to toggle the mute and unmute conditions (toggles `Audible' and `Inaudible'). · Push the key to mute the channel (sets to `Inaudible' only). · Push the key to unmute the channel (sets to `Audible' only). · Push the key after the communication is finished to send a `reset code'. [SCAN A] SCAN START/STOP KEY [SCAN B] Push this key to start scanning; and push again to stop. Push and hold this key to indicate the scan group, then push to select the desired group. and an opening message may appear. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your Dealer. · The keys in the table below can be used for password input: · The transceiver detects numbers in the same block as identical. Therefore "01234" and "56789" are the same. NON-BANK TYPE: Push [CH UP]/[CH DN] to select the desired operating channel, in sequence; or, push one of the [CH 1] to [CH 4] to select a channel directly. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or when taking the microphone off hook. KEY NUMBER [P0] 0 5 [P1] 1 6 [P2] 2 7 [P3] 3 8 [P4] 4 9 e When the "PASSWORD" indication does not clear after inputting 4 digits, the input code number may be incorrect. Turn power off and start over in this case. 7 OPERATION 2 I Receiving and transmitting RECEIVING: q Push [POWER] to turn the power ON. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANSMITTING: r Take the microphone off hook. · 5-tone mute may be released (the `audible' condition is selected and " " appears). · A priority channel may be selected automatically. D Transmitting notes · Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition (`Inaudible' condition; " does not appear). e Push [SCRM] to turn the function OFF. D Tx code number selection If the transceiver has a [CODE] key, Tx code contents can be changed within the allowable digits. TO SELECT A TX CODE: q Push [CODE] -- a Tx code number appears and an allowable digit blinks. w Push [CH UP]/[CH DN] to select the desired number at the blinking digit. [. . . ] fi OPTIONAL CABLE (OPC-617) Connect an external modem unit, LCD backlight control, etc. t 4 I Supplied Accessories q w e r y u i o !0 !1 !2 !3 q Microphone . . . . . . . . . . . . . . . . . . . . . . 1 r DC power cable . . . . . . . . . . . . . . . . . 1 IC-F2010/F610: OPC-345 o Flat washers . . . . . . . . . . . . . . . . . . . . . . 4 !3 Function name stickers* (1705 LCD SEAL(D)) . . . . . . . . . . . . . 1 *Function name stickers There are no names on the programmable function keys since the needed functions can be assigned to these keys. Attach the supplied function name stickers above the appropriate keys. 14 4 CONNECTION AND MAINTENANCE I Mounting the transceiver The front panel can be inverted for correct viewing while leaving the built-in speaker facing away from the mounting surface. [. . . ]