User manual ICOM IC-F210

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF110 UHF TRANSCEIVER iF210 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTION RWARNING!NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. If an incorrect connection is made after cutting, the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F110 VHF TRANSCEIVER and IC-F210 UHF TRANSCEIVER. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. [. . . ] BANK · When the optional UT-105 is installed, push one or more times to select a channel bank for conventional channels or SmarTrunk II TM channels. 3 PANEL DESCRIPTION ¡ SCAN START/STOP KEY Push this key to start scanning; and push again SCAN A to stop. SCAN B 1 ¡ MONITOR KEY Activates one of (or two of) the following functions MONI on each channel independently: · Push and hold the key to unmute the channel (audio is emitted; `Audible' condition). · Push the key to toggle between the mute and unmute conditions (toggles between `Audible' and `Inaudible'). · Push the key to mute the channel (sets to `Inaudible' only). · Push the key to unmute the channel (sets to `Audible' only). · Push the key after communication is finished to send a `reset code'. NOTE: Place the microphone on hook to start scanning. ¡ SCAN TAG KEY Adds or deletes the selected channel to the scan TAG group. ¡ PRIORITY CHANNEL KEYS Push these keys to select priority A or priority B PRI A channel, respectively. PRI B ¡ OPERATING CHANNEL KEYS Select an operating channel directly. CH1 CH2 CH3 CH4 NOTE: The unmute condition (`Audible' condition) may automatically return to the mute condition (`Inaudible' condition) after a specified period depending on the pre-setting. to lock all programmable LOCK keys except the following: · [CALL] (incl. [CAL A] and [CAL B]), [MONI] and [EMER] keys. 4 1 PANEL DESCRIPTION ¡ CALL KEY Transmit a 2-tone, 5-tone code. CALL · Call transmission is necessary before you call another station depending on your signaling system. · The [CAL A] and/or [CAL B] keys may be available when your system employs selective `Individual/Group' calls. Contact your dealer about which call is assigned to each key. ¡ OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily, or H/L permanently, depending on the pre-setting. · Contact your dealer for the output power level for each selection. CAL A CAL B ¡ TALK AROUND KEY Turns the talk around function ON and OFF. TA · The talk around function equalizes the transmit frequency to the receive frequency for mobile-to-mobile communication. ¡ EMERGENCY KEY Push and hold the key to transmit an emergency call. EMER · If you want to cancel the emergency call, push and hold (or push) the key again before transmitting the call. · Depending on the pre-setting, the emergency call is transmitted one time only, or repeatedly, until receiving a control code. ¡ WIDE/NARROW KEY Push this key to toggle the bandwidth between W/N wide or narrow. ¡ DTMF AUTODIAL KEY Push this key to display the text of the DTMF DTMF channel number and set the desired channel number via the [ ]/[ ] key. Then, push this key again to transmit a specified DTMF code. ¡ HOOK SCAN When the Hook Scan function is turned ON, push HOOK this key to stop scanning temporarily. ¡ TX CODE KEY Select a transmit 5-tone code (station code) chanTX CH nel. 5 PANEL DESCRIPTION ¡ SCRAMBLER KEY Push and hold to turn the voice scrambler funcSCRM tion ON. NOTE: · The optional UT-109 (#02) or UT-110 (#02) VOICE SCRAMBLER UNIT is required. ­ UT-109: Non-rolling type. 1020 (4 groups × 255) codes are available. 1 ¡ USER SET MODE KEY Changes the contents of the items in the User Set SET mode. · User set mode also available via the `Power ON function'. · This transceiver requires version #02 of these units. [. . . ] · Memories [A]­[D] are used for the Turbo SpeeDial. 12 4 Antenna CONNECTION AND MAINTENANCE w I Rear panel and connection Optional speaker (SP-22) q red: + R C A U T I O N !Crimp Solder t Optional cable (OPC-617) e r black: 12V Battery NEVER connect to a 24 V battery. 13 CONNECTION AND MAINTENANCE q ANTENNA CONNECTOR Connects to an antenna. w MICROPHONE HANGER Connect the supplied microphone hanger to the vehicle's ground for microphone on/off hook functions. r OPTIONAL CABLE (OPC-617) Connect an external modem unit, dimmer control, etc. [. . . ]