User manual INDESIT BIAA13FWD

[. . . ] - The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us. - Any parts removed during repair work or any appliance that is replaced become our property. - The appliance is used in the United Kingdom or Republic of Ireland. The guarantee does not cover: - Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation. [. . . ] Fitting a new plug IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. . . Green and Yellow - Earth Blue - Neutral Brown - Live As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: - Connect Green and Yellow wire to terminal marked ‘E’ or or coloured Green and Yellow. - Connect Brown wire to terminal marked ‘L’ or coloured red or brown. - Connect Blue wire to terminal marked ‘N’ or coloured Black or Blue. If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse. If you are in any doubt about the electrical supply to your machine, consult a qualified electrician before use. CE Marking certifies that this appliance conforms to the following EEC directives: Low Voltage Equipment - 73/23/EEC & 93/68 EEC Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24 5 GB Start-up and use Starting the appliance !Before starting the appliance, follow the installation instructions (see Installation). Before connecting the appliance, clean the compartments and accessories well with lukewarm water and bicarbonate. The appliance comes with a motor protection control system which makes the compressor start approximately 8 minutes after being switched on. The compressor also starts each time the power supply is cut off whether voluntarily or involuntarily (blackout). 1. Insert the plug into the socket and ensure that the internal light illuminates ( the FREEZER OPERATION knob must not be on the position ) . Make sure that the tank has been properly inserted in the door (see picture). PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24 7 GB Ice3 ice tray The fact that they are situated on the top part of the freezer drawers ensures greater cleanliness: the ice no longer comes into contact with the food placed inside the freezer compartment; furthermore, the dripping of the water during filling is avoided (a lid to cover up the hole after filling with water is also provided). Check that the tray is ompletely empty and fill it with water through the opening provided. Excess water prevents the ice cubes from dispensing (if this happens, wait for the ice to melt and empty the tray). 3. Turn the tray 90°: due to the connected compartments each mould fills with water (see diagram). 4. Close the opening with the lid provided and put the tray back, placing the top part in the corresponding housing and allowing it to drop in again. 5. When the ice has formed (minimum time approximately 8 hours) knock the tray against a hard surface and wet the outside so that the ice cubes come loose and take them out through the opening. Replacing the light bulb • We recommend you clean your fridge with our Professional Fridge cleaner. To order please call us on 08448 225 225 or visit www. indesitservice. co. uk To replace the light bulb in the refrigerator compartment, pull out the plug from the electrical socket. Access the light bulb by removing the cover as indicated in the diagram. Replace it with a similar light bulb within the power range indicated on the cover. 1 2 1 Precautions and tips MAX WATER LEVEL !The appliance was designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully. This appliance complies with the following Community Directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments; -89/336/EEC of 03. 05. 89 (Electromagnetic Compatibility) and subsequent amendments; - 2002/96/CE. WATER LEVEL MAX Maintenance and care Switching the appliance off During cleaning and maintenance it is necessary to disconnect the appliance from the electricity supply: 1. set the FREEZER OPERATION knob on 2. pull the plug out of the socket Cleaning the appliance • We recommend you clean your fridge with our Professional Fridge cleaner. To order please call us on 08448 225 225 or visit www. indesitservice. co. uk • The external and internal parts, as well as the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and bicarbonate of soda or neutral soap. [. . . ] It is not sufficient to set the temperature adjustment knobs on (appliance off) to eliminate all electrical contact. • In the case of a malfunction, under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or further malfunctioning of the appliance. • Do not use any sharp or pointed utensils or electrical equipment - other than the type recommended by the manufacturer - inside the frozen food storage compartments. [. . . ]