User manual INDESIT D 63

[. . . ] Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 2. After removing the packing, check to make sure that the appliance is not damaged. 3. The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. [. . . ] Arrange the rack with the back wheels in either the top or bottom position and then insert it along the guides until the front wheels are on as well. Lower Rack Upper Rack Load for 12 Standard Settings (For IEC- EN 50242: upper rack at top position) Lower Rack Upper Rack Normal Daily Load fig. F 4 5 GB Turning on the Appliance Starting a wash cycle. . . . Make sure that the plug for the appliance is inserted into the wall socket. Load the dishwasher (see the section entitled, "Loading the Dishwasher"). Pour in the detergent (see the section entitled, "Salt, Detergent and Rinse Aid"). Turn the knob located on the right of the control panel in the clockwise direction until the number or symbol for the cycle setting is aligned with the reference mark (see the section entitled, "Wash Cycle Table"). Cancelling or modifying a wash cycle setting. . . Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). Press the ON-OFF button, and the ON light will turn off. Rotate the knob in the clockwise direction to the desired cycle setting (see the section entitled, "Starting a wash cycle. . . "). When the knob stops turning and is aligned with a STOP mark (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water supply and open the door of the dishwasher. STOP Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. Wash Cycle Adjustment Buttons "Intensive 65°C" Button This button (see "Close-up View - Control Panel", letter "E") is used with the normal cycle in the case where pots and pans with dry caked-on food must be washed. This is not recommended for delicate items in so far as the high temperatures could make their surfaces opaque or lighten decorative colors after repeated washing. "Half Load "Button" This button (see "Close-up View - Control Panel", letter "F") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. It can be used before setting any of the wash cycles, except for the intensive cycles (if included in the wash cycle table). Please keep in mind that the amount of detergent should also be cut in half. GB 6 Wash Cycle Table Cycle INTENSIVE 65°C Button Cycle Selection Information Description of Cycle Detergent for Pre-wash + Wash Rinse Aid 1) Normal Wash 55°C (IEC-EN 50242) Normally dirty dishes, pots and pans. Drying. 8+22gr. * 1) Normal Wash Very dirty dishes, pots and pans (not to be used with delicate items). Pre-wash with cold water. Drying. 8+22gr. * 2) Reduced Wash 55°C Normally dirty dishes, pots and pans without dried-on residue. Pre-wash with cold water. Drying. 4+22gr. * 3) Delicates Wash 50°C Economic, fast cycle to be used for items which are sensitive to higher. [. . . ] Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see figure 2). If the water pipes are new or A have not been used for an extended period of time, let the water run to make sure that the water is clear and free of Fig. 2 impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. [. . . ]