User manual INDESIT DE 73

[. . . ] Dishwasher Instructions for installation and use DE 73 DE 73 Dishwasher Installation and use Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 6. This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. 8. Do not lean or sit on the door when it is open, as this could overturn the dishwasher. [. . . ] To select a new wash cycle, repeat the instructions contained in the paragraph entitled "Starting and setting the cycle" If you have left out a dish. . . You can interrupt a wash cycle by pressing the ON-OFF button, then place the forgotten dishes into the appliance, which will start up from where it was interrupted when you turn it back on. Cycle phase underway indicator Your dishwasher is equipped with an indicator "G" comprising 4 symbols which represent the different phases of a wash cycle. When the wash cycle has started, the display will indicate the phases underway in sequence. The end of the wash cycle is signalled by 2 beeps, and a flashing "END" will come up on the display. Bring the selector back to the RESET position, and the 3 dashes for programming cancellation will appear. Turn the appliance off by pressing the ON-OFF button, turn off the water tap and open the door. Wait a few minutes before removing the dishes: this way you won't have to handle them while they're still hot and they will dry better. How to eliminate the drying phase. To eliminate the drying phase from the wash cycle you wish to start, just turn the knob to the Reset position then first and foremost set any preferences as to: Þ Þ upper or lower rack delayed start Start the wash cycle by following the instructions. Symbol relating to the drying phase will flash for approximately 4 seconds; immediately press button "I" and the symbol will disappear, thus indicating that the drying phase has been eliminated. 7 GB Dishwasher delayed start programming Dishwasher delayed start programming Premise: before selecting a wash cycle as indicated in the paragraph entitled "Starting and setting a wash cycle. . . ", a delayed start can be set. Press button "D" (see close-up view "control panel") to delay the start of a wash cycle by 1 to 24 hours. Each time you press the button, the counter "L" will display the number of hours the cycle start has been delayed by in sequence; choose the time you prefer. The delayed start indicator light "H" flashes and when the appliance starts, the counter will begin the countdown to the delayed start. When this time is up, the wash cycle will begin and the counter will now serve to display the amount of time left until the end of the wash cycle. NOTE: Wash cycle modification buttons Half load selection button on upper or lower rack. Cold rinse. 22 g. 5) Rapid 25' 6) Hot Rinse To be used for dishes that only need to be rinsed. Hot rinse at 70°C. Drying. * 7) Soak Preliminary wash cycle for dishes and pans awaiting completion of the load with the dishes from the next meal. Short cold wash to prevent food from drying onto the dishes. 9 GB Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. - Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. - There is no utility in rinsing dishes, cookware and utensils before placing them in the dishwasher. How to Keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. Remove the Plug Before cleaning or performing maintenance, always remove the plug from the socket. [. . . ] Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see figure 2). If the water pipes are new or have not been used for an A extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is Fig. 2 not taken, there is a risk that the water inlet can get blocked and damage the appliance. [. . . ]