User manual INDESIT DE43

[. . . ] Dishwasher Instruction for installation and use DE 43 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 2. After removing the packing, check to make sure that the appliance is not damaged. 3. The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. [. . . ] If you press the button once more, the selection will be reset and the dishwasher will consequently wash on both racks. To use the racks correctly, we recommend you read the chapter entitled "Loading the dishes". Cycle phase under way indicator Your dishwasher is equipped with an indicator "G" comprising 4 symbols which represent the different phases of a wash cycle. When the wash cycle has started, the display will indicate the phases under way in sequence. These phases are: this point, all the settings will have been cancelled. To select a new wash cycle, repeat the instructions contained in the paragraph entitled "Starting and setting the cycle". You can interrupt a wash cycle by pressing the "ON-OFF" button, then place the forgotten dishes into the appliance, which will start up from where it was interrupted when you turn it back on. The wash cycle stops and then restarts when the electricity comes back on or when you shut the door. If you want your dishes to be perfectly dry, follow the instructions below. Set the knob to RESET and make any specific settings, such as: upper or lower rack delayed start Start the wash cycle by turning the knob and open the appliance door. Observe symbol for drying: it will flash for about 4 seconds, while the word "OFF" appears on the display (extra drying disabled). If you press button "I" immediately, you will hear a prolonged beep and the word "ON" will appear on the display: the extra drying has been enabled. A quick look at the indicator lights will keep you informed of the countdown progress at all times. w During the countdown, you can modify the delay by pressing button "D" repeatedly without resetting the wash cycle. w If you have changed your mind and wish to start the wash cycle immediately, press button "D" until the countdown is fully reset. Indicator light "H" will turn off and the cycle will start at the sound of a beep. The indicator light corresponding to the cycle phase under way will come up on the display and the countdown to the estimated cycle end begins. 7 GB Wash Cycle Table Detergent for prewash + wash Rinse Aid Cycle Cycle selection instructions Cycle description 1) Intensive Very dirty dishes and pans (not to be used for delicate items). Pre-wash with cold water Pre-wash with hot water at 45°C Extended wash at 70°C. Drying. 5+15 gr. * 2) Normal Normally dirty pans and dishes. Drying. 5+15 gr. * 3) Rapid 25' Economic and fast cycle to be used for slightly dirty dishes. Cold rinse. 15 gr. 4) Soak Preliminary wash cycle for dishes and pans awaiting completion of the load with the dishes from the next meal. Short cold wash to prevent food from drying onto the dishes. 5) Crystal care Economic and fast cycle to be Wash at 50°C. Drying. 15 gr. * Normally dirty pans and 6) After dinner dishes with no dry residue. 5+15 gr. * Economic and fast cycle to be Short wash at 45°C. Drying 15 gr. * GB 8 Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. [. . . ] Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see figure 2). If the water pipes are new or have not been used for an extended period of time, let the A water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the Fig. 2 water inlet can get blocked and damage the appliance. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60° C. [. . . ]