User manual INDESIT DI6

[. . . ] 4. Fundamental rules to follow when using the appliance: - Never touch the dishwasher when barefoot or with wet hands or feet; - We discourage the use of extension cords and multiple sockets; - During installation, the power supply cord must not be excessively or dangerously bent or flattened; To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: l call only the Service Centers authorized by the manufacturer l always use original Spare Parts Close-up View (control panel) C P B A 1 2 3 4 ON-OFF Button ON - OFF Light Cycles Indicator Lights Cycles Indicator Lights P Cycle select button 11 GB Close-up View (Interior) E G F H J K I L Upper Rack Top Sprayer Arm Rack Height Adjustor Lower Rack Bottom Sprayer Arm Salt Container Cap Washing Filter Detergent and Rinse Aid Dispenser Technical characteristics Width Depth Height Capacity Mains water pressure Power voltage Total absorber power Fuse cm. 82 12 standard place settings 30 KPa÷ 1MPa (0, 3 ÷10 bar) See data plate See data plate See data plate GB 12 Salt . . . . . . . Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. [. . . ] The top rack can be adjusted using the two rack heights (top and bottom). To adjust the rack, open up the tabs that lock the guides and pull out the rack. Arrange the rack with the back wheels in either the top or bottom position and then insert it along the guides until the front wheels are on as well. A Lower Rack Upper Rack 1 2 3 4 15 GB Starting the Appliance Starting a wash cycle. . . . After performing all the operations described in the previous paragraphs, turn the water tap on completely, open the appliance door and press ON-OFF button "A": indicator light "B" comes on. Setting and Starting a Wash Cycle Select the wash cycle by pressing button "P". Each time this button is pressed, one of the indicator lights "C" will come on in sequence, select the wash cycle you deem most suitable for the type of dishes to wash (take a look at page 17, where you will find the wash cycle table). Close the appliance door and after a few seconds, you will hear a short beep: the wash cycle has begun. Premise: A cycle that is underway can only be modified if it has only been running for a short time. Open the appliance door carefully to avoid any hot water splashes, then keep button "P" pressed for approximately 5 seconds, until you hear 3 short beeps. Indicator light "C" will come off and at this point, all the settings will have been cancelled. Interrupt the wash cycle by opening the appliance door with the utmost care, as usual, then insert the dish you had forgotten. When you shut the appliance door, the cycle will start up from where you interrupted it. The wash cycle stops and then restarts when the electricity comes back on or when you close the door. The end of the wash cycle is indicated by a double beep and the flashing of the wash cycle indicator light "C". Open the dishwasher door, press the ON-OFF button as well, thus cutting off the electricity supply to the appliance. Warning If opening the door soon after the end of the programme, or during it, stand away from the Dishwasher, to avoid possible injury from hot steam. GB 16 Wash Cycle Table Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer, cleaner results. &\FOH &\FOH VHOHFWLRQ LQVWUXFWLRQV &\FOH GHVFULSWLRQ 'HWHUJHQW IRU SUHZDVK ZDVK 5LQVH $LG :DVK F\FOH GXUDWLRQ WROHUDQFH   , QWHQVLYH Very dirty dishes, pots and pans (not to be used with delicate items). Pre-wash with hot water at 40°C Extended wash at 65°C. Standard daily cycle. JU  1RUPDO Pre-wash of dishes, pots and pans while waiting for the load to be completed after the subsequent meal. Short cold wash to prevent food residue from drying on the dishes.  6RDN Environmentally-friendly cycle, with low energy consumption levels, suitable for normally dirty pans and dishes. 2 Cold pre-washes Extended wash at 50°C Hot rinse at 65°C Drying J  (FR 17 GB Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. For this reason, it is a good idea to D C remove the larger food particles trapped inside the semi-circular filter A and cup "C"after each wash; to remove the filter assembly, pull the cup handle B upwards. A The entire filter assembly should be cleaned thoroughly once a month: semi-circular filter A + cup C + cylindrical filter B+ microfilter D. Reassemble the filter parts (as shown in the figure) and reinsert the whole assembly into the dishwasher. [. . . ] In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adpators or the like as they could cause overheating and burns. [. . . ]