User manual INDESIT DI67

[. . . ] DI 67 Dishwasher Installation and use Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 2. After removing the packing, check to make sure that the appliance is not damaged. 3. The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. [. . . ] The top rack can be adjusted using the two rack heights (top and bottom). To adjust the rack, open up the tabs that lock the guides and pull out the rack. Arrange the rack with the back wheels in either the top or bottom position and then insert it along the guides until the front wheels are on as well. F). Bottom Rack Top Rack Load for 12 Standard Settings Bottom Rack Top Rack Normal Daily Load A 1 2 3 Fig. After having completed all of the installation steps in the preceding paragraphs, turn on the water to the unit and press the ON-OFF button (A) located on the control panel. Turn the cycle selector knob "D" until the reference notch on the knob corresponds with the symbol for the cycle you wish to set (have a look at the wash cycle table on page 7). After a few seconds, you will hear a short beep and the indicator light "G" comes on, indicating that the wash cycle has begun and it is not advisable to make any changes at this point. Cycle phase indicator lights The dishwasher is provided with 4 indicator lights "G" which come on in sequence as the appliance is performing that specific phase of the wash cycle. These phases are, from left to right: pre-wash, wash, rinses, drying If you forget to load some of the dishes. . . The end of the wash cycle is signalled by 2 short beeps and a flashing drying phase indicator light "G". Turn the appliance off by pressing button "A", thus cutting off the electricity supply. The wash cycle stops and then restarts when the electricity comes back on or when you close the door. Cancelling or modifying a wash cycle in progress. . . . . Premise: You can cancel the wash cycle in progress, if it has only just started. To modify a wash cycle in progress, turn the knob anticlockwise and set it to Reset, after a few seconds you will hear 3 beeps and indicator light "G" will go out: this means all the settings have been cancelled. You are now free to reset the correct wash cycle. Warning: if opening the door soon after the end of the programme, or during it, stand away from the Dishwasher, to avoid possible injury from hot steam Wash Cycle Adjustement Button "1/2 LOAD" Button This button (see "Close-up View - Control Panel", letter "N") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will help the seals last longer and prevent odors from forming within the appliance. Moving the Appliance If the appliance must be moved, try to keep it in the vertical position. Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occuring. GB 8 Cleaning and Special Maintenance Filter Assembly If you want consistent good results from your dishwasher, you need to clean the filter assembly. The food particles are removed from 1 the wash water, allowing it to be A B 2 recirculated during the cycle, filtered perfectly. For this reason, it is a good idea to remove the C larger food particles trapped inside the cup "C" and the semi-circular filter A after each wash; pull the cup handle upwards to remove them. The entire filter assembly should be cleaned thoroughly once a month: cup C + semi-circular filter A + cylindrical filter B. [. . . ] This dishwasher model can be built-in under the one worktop, and it therefore comes provided with an assembly kit complete with an instructions sheet. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see figure 2). If the water pipes are new or have not been used for an extended period of time, let the A water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that F ig. 2 the water inlet can get blocked and damage the appliance. [. . . ]