User manual INDESIT FIMDE23IX

[. . . ] That the washing machine is levelled properly; something worth checking to aid the performance of your washing machine; 4. That the drum's fixing screws have been removed from the back of the washing machine. 2. 12) With just a bit of care, it will repay you with loyalty and devotion. With the necessary upkeep, it will wash for years and years to come. A correct distribution of your laundry is vital to the successful outcome of the wash and the life of the washing machine. [. . . ] One last secret: when washing with cold water, always reduce the amount of detergent you use: it dissolves less easily in cold water than in hot water, so part of it would be wasted. 4 3 In compartment 1: Detergent for pre-washing (powder) In compartment 2: Detergent for washing (powder or liquid) 1 2 In compartment 3: Additives (softeners, perfumes, etc. ) In compartment 4: Bleach and delicate bleach. Bleach cycle and stain removal button If bleaching is necessary, the extra case 4 (provided) must be inserted into compartment 1 of the detergent dispenser. When pouring in the bleach, be careful not to exceed the "max" level indicated on the central pivot (see illustration). The use of the additional bleach container excludes the possibility of using the pre-wash cycle. Traditional bleach can only be used on sturdy white fabrics, whereas delicate bleach can be used for coloured fabrics, synthetics and for wool. The detergent dispenser can be removed and cleaned: pull it outwards, as indicated in the figure. Then leave it under running water for a few minutes. Cutting costs efficiently A guide to environmentally friendly and economic use of your appliance. MAXIMISE THE LOAD SIZE Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry. Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme. SAVE energy and time by selecting the highest suitable spin speed to reduce the water content in laundry before using a drying programme. You cannot bleach with the "Silk" programme and with the "special programmes" (see page 4). Should you want to do it separately you must pour the bleach into the additional container 4, press button H (stain removal), star t the washing machine, then select one of the symbols according to the type of fabric. When you bleach during a normal wash cycle, pour the detergent and any additives in the special compar tments, press button H (stain removal), set the programme you desire and turn the washing machine on. 7 Instructions for installation and use Troubleshooting Before calling, read the following In most cases, when your washing machine fails to work, the problems arising can be easily solved without having to call for a technician. The washing machine fails to start. Is the plug correctly inserted into the socket?Check whether the definition on its label reads "for machine wash" or "hand and machine wash", or any other similar wording. An excessive amount of detergent, besides producing too much foam, does not guarantee a more effective wash, and causes scaling in the internal parts of the appliance. If, despite all checks, the washing machine fails to function and the problem persists, call your nearest authorised Customer Service Centre, providing the following information: - the nature of malfunction - the model type no. . . . . ) - the serial number (S/N . . . . ) This information can be found on the data plate situated at the back of the washing machine. The washing machine leaks. Is the metal ring of the inlet hose properly attached?Turn off the water supply, unplug the appliance and try tightening its attachment without forcing it. Turn off the water supply, unplug the appliance and try tightening its attachment. Excessive vibration during the spin cycle. Have all transit screws been removed durind installation?Adjust the feet and check them with a level. Always get assistance from authorised technicians and always insist on original spare parts. Technical characteristics Model Dimensions FIMDE23IX width 59, 5 cm height 85 cm depth 52, 5 cm from 1 to 5 kg voltage 230/240 Volt 50 Hz maximum absorbed power 2050 W maximum pressure 1 MPa (10 bar) minimum pressure 0, 05 MPa (0, 5 bar) drum capacity 40 litre up to 1000 rpm Capacity Electrical connections Water connections Spinning speed Control programs in programme 3; temperature 60°C; carried out with 5 kg load. compliance with IEC regulation 456 This appliance conforms with the following E. E. C. directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications 9 Instructions for installation and use Installation and removal When the new washer arrives Whether new or just transported to a new house, installation is extremely important for the correct functioning of your washing machine. After removing the appliance from its packaging, check that it is intact. The inside of the machine is supported, for transportation, by 3 screws on the back panel. Connection to the water mains Both hot and cold water supplies are preferable and they should be between 34. 5kN/m²(5lb/in²) and 1034. 2kN/m² (150lb/in²) pressure. [. . . ] the machine should not be installed in an outdoor environment, not even when a roof shelters the area, because it may be very dangerous to leave it exposed to rain and thunderstorms. It must only be used by adults and exclusively for washing clothes following the instructions provided in this manual. Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never touch the washing machine when barefoot or with wet or damp hands or feet. [. . . ]