User manual INDESIT FV1 GB

[. . . ] Step 1 Pull the water container towards you and remove it completely from the dryer. Step 2 Empty all the water in the water container. Step 2 Pull out the filter (using two fingers). Step 3 Replace the water container making sure that it is securely fixed. Step 3 Clean off any fluff build-up on the internal surface of the filter. Failure to empty the water container may cause the following: - The dryer stops heating (thus the load may still be damp at the end of the drying cycle). - The Empty water container LED activates to show that the water container is full. Filling of the Water Container Step 4 Replace the filter never operate the dryer without the filter in place. When the dryer is first used water will not immediately enter the water container as the pump needs to be primed. This is done automatically and will take a few minutes, during this period the efficiency of the drying process is not affected. 2 Condenser unit - remove any fluff build-up from the condenser on a monthly basis. Step 1 Open the condenser cover - grip the handle and pull towards you. EN Step 2 Remove the condenser by turning the 3 catches, then pull the condenser towards you. (It is normal for some residual water to be left in the tubes). Step 3 Clean the condenser with running water over the rear side to remove any fluff deposits. Step 4 Replace the condenser unit; make sure that the unit is securely in place, that all 3 catches are fixed and that the position arrows on the front end of the condenser are pointing upwards. Failure to clean the condenser unit may cause premature failure of the dryer. 3 Installation EN Where to install the tumble dryer Install the dryer far from gas ranges, stoves, radiators or hobs, as flames may damage it. [. . . ] The selected time is displayed after the start of the programme and cannot be modified after pressing the START/PAUSE button. Delay Start The start of some programmes (see Programmes and options) may be delayed up to 24 hours. Before setting a delayed start, make sure that the water container is empty and that the filter is clean. Pre Anti-Crease When this option is selected in addition to the Delay start option, the drum rotates garments at intervals during the delay period to avoid creases forming. Post Anti-Crease When this option is selected, the drum rotates garments at intervals after the cold drying cycle has ended, in order to avoid creases forming on garments if they cannot be immediately removed at the end of the programme. High Heat When a drying time is selected, pressing this button sets a high heat drying and the indicator light above the button lights up. Alarm A buzzer sounds at the end of the drying cycle to signal that the programme has ended and the garments are ready to be removed. Not all options are available on all programmes (see Programmes and options). If the button of an unavailable option is pressed, the buzzer emits three signals. If an option is available, a single buzzer signal sounds and the option indicator light next to the button lights up to confirm the selected option. Opening the door If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following may occur: The START/PAUSE button flashes orange. It is necessary to press the START/PAUSE button to resume the Delay start programme. The Timed drying settings are also indicated to enable you to select the most suitable timed option. The weight refers to dry items. Drying times Drying times are approximate and may vary depending on the following: Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water. Fabrics: items of the same fabric, but with different texture and thickness may have different drying times. Amount of laundry: single items and small loads may take longer to dry. Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete drying can be left longer. Automatic drying times Cotton High heat Drying tim es after 800-1000 rpm wash cycles Half load 2 kg 3 kg 4 kg 5 kg 6 kg 0:40-0:55 0:55-1:10 1:10-1:20 1:20-1:30 1:35-2:00 1:00 or 1:30 1:00 or 1:30 1:30 or 2:00 1:30 or 2:00 2:20 or 2:40 Full load 7. 5 kg 2:00-2:40 2:20 or 3:00 Autom atic (hrs:m ins) Tim ed (hrs:m ins) S ynthetics Low heat 1 kg 0:30-0:40 0:30 or 1:00 7 kg 2:20-2:30 2:20 or 2:40 Autom atic (hrs:m ins) Tim ed (hrs:m ins) Acrylics Low heat Drying tim es after wash cycles at lower speeds Half load 1 kg 2 kg 0:40 - 0:50 0:50 - 1:10 0:30 or 1:00 0:30 or 1:00 Full load 3 kg 1:10 - 1:30 1:00 or 1:30 Autom atic (hrs:m ins) Tim ed (hrs:m ins) Drying tim es after wash cycles at lower speeds Half load 1 kg 0:40 - 1:00 0:30 or 1:00 or 1:30 Full load 2 kg 0:55 - 1:15 1:00 or 1:30 or 2:00 12 Warnings and suggestions !This appliance was designed and manufactured in compliance with current international safety standards. The following information is provided for safety reasons and must be read carefully. Do not tumble dry large, excessively bulky items. Do not switch the tumble dryer off if items that are still warm are inside it. Empty the water container and put it back in place after each use (see Care and maintenance). Avoid climbing on the top of the dryer as this may damage the appliance. [. . . ] 15 Assistance Before calling the Technical Assistance Centre: EN Spare parts This dryer is a complex machine. Attempting to repair it personally or with the aid unqualified personnel may put the safety of people at risk, damage the machine or invalidate the spare parts guarantee. Always contact a qualified technician when experiencing problems with this machine. The spare parts were designed exclusively for this machine and should not be used for any other purpose. Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting). [. . . ]