User manual INDESIT GCO120

[. . . ] - The Empty water container LED activates to show that the water container is full. Filling of the Water Container Step 4 Replace the filter never operate the dryer without the filter in place. When the dryer is first used water will not immediately enter the water container as the pump needs to be primed. This is done automatically and will take a few minutes, during this period the efficiency of the drying process is not affected. 2 Condenser unit - remove any fluff build-up from the condenser on a monthly basis. Step 1 Open the condenser cover - grip the handle and pull towards you. EN Step 2 Remove the condenser by turning the 3 catches, then pull the condenser towards you. (It is normal for some residual water to be left in the tubes). Step 3 Clean the condenser with running water over the rear side to remove any fluff deposits. Step 4 Replace the condenser unit; make sure that the unit is securely in place, that all 3 catches are fixed and that the position arrows on the front end of the condenser are pointing upwards. Failure to clean the condenser unit may cause premature failure of the dryer. 3 Installation EN Where to install the tumble dryer Install the dryer far from gas ranges, stoves, radiators or hobs, as flames may damage it. If the dryer is installed below a worktop, ensure there are 10 mm between the upper panel of the dryer and any objects above it, and 15 mm between the sides of the machine and the walls or furniture units adjacent to it. [. . . ] Not all options are available on all programmes (see Programmes and options). Opening the door If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following may occur: The START/PAUSE button flashes orange. It is necessary to press the START/PAUSE button to resume the Delay timer programme. One of the Delay timer indicator light flashes to signal the delay time entered. It is necessary to press the START/PAUSE button to resume the programme. The progress indicator lights signal the running phase and the START/PAUSE indicator light stops flashing and turns green. Pressing the START/PAUSE button reactivates a new programme from the beginning. By turning the Programme selection knob, a new programme is selected and the START/PAUSE indicator light flashes green. This procedure can be used to select the Cold drying programme to cool garments if they are judged to be dry enough. Note: In the event of a power cut, turn the power switch off and remove the plug; when the electricity supply returns, press the START/PAUSE button to resume the programme. 10 Laundry Sorting laundry Check the symbols on the care labels of the various garments to verify whether the garments can be safely tumble dried. Close zips and hooks and fasten belts and strings without tightening them. Wring out garments to remove the maximum amount of water possible. Care labels Always check the care labels, especially when placing garments in the tumble dryer for the first time. This tumble dryer must not be used by persons (including children) with physical, sensory or mental impairments or with little experience and knowledge of the appliance, unless they are supervised or have been adequately instructed on its use by the person responsible for their safety. Children must be supervised to ensure that they do not play with the appliance. The appliance must be correctly installed and receive adequate ventilation. The air intake on the front part of the dryer and the air vents on the rear must never be obstructed (see Installation). Never use the dryer on carpeting with high pile as this may prevent air from entering the dryer from the base. The rear part of the dryer may become very hot: do not touch it while the appliance is in function. Do not use the dryer unless the filter, water container and condenser are properly positioned (see Maintenance). Do not use liquid fabric softener in the dryer; add it to the final rinse of the wash cycle. Tumble dry items only if they have been washed with water and detergent, and have been rinsed and put through a spin cycle. Drying items that have NOT been washed with water may cause the risk of fire. Always read the instructions on the care label carefully (see Laundry). [. . . ] It occurs after 30 minutes: - if you leave the dryer without starting a programme; - after your drying programme has finished. Press the On/Off button and the lights will come on again. 15 Assistance EN Before contacting the Technical Assistance Centre: Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting). If not, switch the dryer off and contact the Technical Assistance Centre closest to you. Provide the following data when contacting the Technical Assistance Centre: name, address and postal code telephone number type of malfunction date of purchase the appliance model (Mod. ) the dryers serial number (S/N) This information can be found on the data plate located behind the door. Spare parts This dryer is a complex machine. [. . . ]