User manual INDESIT IDL 40

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual INDESIT IDL 40. We hope that this INDESIT IDL 40 user guide will be useful to you.


INDESIT IDL 40 : Download the complete user guide (2610 Ko)

You may also download the following manuals related to this product:

   INDESIT IDL 40 (3729 ko)
   INDESIT IDL 40 (3729 ko)
   INDESIT IDL 40 (3729 ko)
   INDESIT IDL 40 (3729 ko)
   INDESIT IDL 40 (3729 ko)

Manual abstract: user guide INDESIT IDL 40

Detailed instructions for use are in the User's Guide.

[. . . ] Technical characteristics Width Depth Height Capacity Mains water pressure Power voltage Total absorber power Fuse cm. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: 1. [. . . ] Arrange the rack with the back wheels in either the top or bottom position and then insert it along the guides until the front wheels are on as well. Turn on the water tap completely and press ON-OFF button "A". You will hear a short beep and indicator light "B" lights up. Turn the cycle selector knob "D" clockwise until the reference notch on the knob corresponds with the number or symbol for the cycle you wish to set (consult the wash cycle table on page 17, especially when first using the appliance). If the appliance door is shut, press the Start button "R" and you will hear a beep; the cycle will start up within a few seconds. Cycle phase indicator lights The dishwasher is provided with 4 indicator lights "G" which come on in sequence as the appliance is performing that specific phase of the wash cycle. You can interrupt a wash cycle by pressing the ON-OFF button, then place the dishes you had left out into the appliance, which will start up from where it was interrupted when you turn it back on. The wash cycle stops and then restarts when the electricity comes back on or when the door is shut. The end of the wash cycle is indicated by two short beeps and the flashing of the drying phase indicator light. Wait a few minutes before unloading the dishes: if you wait a little while, they dry better thanks to the steam. Warning: when you open the dishwasher door after the wash cycle has just ended or is under way, take care not to scald yourself with the hot steam. Premise: You can cancel the wash cycle in progress, if it has only just started. To modify a wash cycle, keep the RESET button "R" pressed for about 5 seconds: a prolonged beep will sound, followed by three short beeps. Indicator light "G" will turn off and at this point, all the settings will have been cancelled. To select a new wash cycle, repeat the operations illustrated in the paragraph entitled "starting and selecting the cycle". Warning: the knob must be turned clockwise from wash cycle 1 to 4, an anti-clockwise from wash cycle 4 to 1. Environmentally-friendly cycle, with low energy consumption levels, suitable for normally dirty pans and dishes. Preliminary wash cycle for dishes and pans awaiting completion of the load with the dishes from the next meal. - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. - Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. [. . . ] In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Drain Hose Connection Fit the drain pipe into a drain line with a minimum diameter of 4 cm or place it over the sink. Use the special plastic elbow provided (see figure) to position it in the best possible way. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE INDESIT IDL 40




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual INDESIT IDL 40 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.