User manual INDESIT VIA 640 C

[. . . ] This appliance is intended for domestic use and conforms to the EC directives currently in force. The appliance has been built to carry out the following functions: cooking and heating up food; all other uses are considered unsuitable. The manufacturer declines all responsibility for uses other than those indicated. If the appliance is installed on caravans or boats, it must not be used to heat rooms. [. . . ] Do not allow unsupervised children to perform cleaning or maintenance operations. Do not insert pointed metal objects (cutlery or utensils) into the slots in the appliance. The steam could reach the electronics, damaging them and causing shortcircuits. All repairs must be carried out by an authorised technician or at an authorised service centre. Do not spray any spray products near the household appliance while it is in operation. The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spare parts. 6 Instructions for disposal 3. ENVIRONMENTAL CARE 3. 1 Our environmental care Pursuant to Directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating to the reduction of the use of hazardous substances in electrical and electronic appliances, as well as to the disposal of refuse, the crossed out bin symbol on the appliance indicates that at the end of the useful life of the product, it must be collected separately from other refuse. Therefore, the user must consign the product that has reached the end of its working life to the appropriate selective collection centres for electrical and electronic refuse, or deliver it back to the retailer when purchasing an equivalent product, on a one for one basis. Adequate selective collection for the subsequent forwarding of the decommissioned product to recycling, treatment and ecologically compatible disposal contributes to avoiding possible negative effects on the environment and on health and promotes the recycling of the materials of which the appliance consists. Illicit disposal of the product by the user will lead to the application of administrative sanctions. The product does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current European directives. 3. 2 Your environmental care Our product's packaging is made of non-polluting materials, therefore compatible with the environment and recyclable. NEVER USE A JET OF STEAM TO CLEAN THE APPLIANCE. WARNING: For your safety, before performing any cleaning or extraordinary maintenance, it is recommended to use protective gloves. 5. 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly after use. 5. 1. 1 Ordinary daily cleaning To clean and preserve stainless steel surfaces, use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather. 5. 1. 2 Food stains or residues Do not use metallic sponges or sharp scrapers as they will damage the surface. Use ordinary non-abrasive products for steel, with the aid of wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 5. 2 Cleaning the cooking hob parts For easier cleaning the pan stands, burner caps, flame spreader crowns and burners can all be removed; wash them with warm water and non-abrasive detergent making sure to remove any encrustation, then wait until they are perfectly dry. Replace the burner caps on their corresponding crowns as indicated in "4. 1 Lighting the hob burners". For correct operation the igniters and thermocouples must always be perfectly clean. Remove any dry residues with a wooden toothpick or a needle. 10 Instructions for the installer 6. POSITIONING IN THE COUNTER TOP The following operation requires building and/or carpentry work and must therefore be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 6. 1 Fixing to the traditional built-in model support structure 1 51 86 Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge. [. . . ] Carefully screw up the adapter unit 3 to the gas fitting 1 of the appliance interposing the gasket 2. 1 2 3 17 Instructions for the installer 7. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the power supply. The appliance is preset for natural gas G20 (2H) at a pressure of 20 mbar. In case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas taps. [. . . ]