User manual INDESIT VRM 641 D X

[. . . ] 9 USING THE HOB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CLEANING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 POSITIONING IN THE COUNTER TOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 ELECTRICAL CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS, DO NOT USE IT AS A ROOM HEATER. DO NOT USE THIS APPLIANCE FOR HEATING ROOMS. THIS APPLIANCE IS MARKED ACCORDING TO EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). Adequate selective collection for the subsequent forwarding of the decommissioned product to recycling, treatment and ecologically compatible disposal contributes to avoiding possible negative effects on the environment and on health and promotes the recycling of the materials of which the appliance consists. The illicit disposal of the product by the user results in the application of administrative sanctions. The product does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current European directives. 3. 2 Your environmental care Our product's packaging is made of non-polluting materials, therefore compatible with the environment and recyclable. You can obtain the addresses of collection, recycling and disposal centres from your retailer or from the competent local organisations. Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. Important: hand over your appliance to the local agency authorised for the collection of household appliances no longer in use. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 8 Instructions for the user 4. DESCRIPTION OF CONTROLS 4. 1 Control zone All the hob controls are grouped together on the front panel. 6. 1. 2 Food stains or residues Do not use metallic sponges or sharp scrapers: they will damage the surface. Use ordinary non-abrasive products, together with anti-scratch sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 15 Instructions for the user 6. 2 Cleaning the acid-etched glass hob 6. 2. 1 Grease Use washing up liquid and a microfibre cloth. 6. 2. 2 Rings and encrustations Use stainless steel cream Crema Inox or mildly abrasive creams; leave the product to act for a few minutes, then wipe away with a microfibre cloth. This appliance can be mounted against walls higher than the work surface on condition that a distance be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure there is a minimum distance of 750 mm between the hob burners and any shelf or hood that may be installed directly above it. 7. 2 Hob seal To prevent leakage of liquid between the frame of the hob and the work surface, place the seal provided along the entire outer edge of the hob before assembly. Do not fix the hob using silicon as this would make it impossible to remove the hob, if necessary, without damaging it. 18 Instructions for the installer If installed on top of an oven, the latter must be equipped with a cooling fan. In case of installation on an empty kitchen unit with doors, a separation panel must be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the hob and the surface of the panel, which must be easily extractable to allow sufficient access for any technical assistance. 19 Instructions for the installer 7. 3 Fixing using brackets The figure to the side shows the exact holes to be used to correctly attach the hob to the work surface with brackets. Fix the hob to the unit using the appropriate brackets supplied. To secure the hob correctly to the counter top, tighten the brackets A in the appropriate holes on the sides of the casing. Take care while securing with the brackets; if tightened too much the glass may be strained causing it to crack. 20 Instructions for the installer 8. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. Pass the power supply cable through the back of the unit, taking care that it does not touch the bottom casing of the hob or the oven (if any) installed underneath it. Fit the power supply line with a multipolar cut-out device with a contact opening gap equal to or greater than 3 mm in an easily accessible position close to the appliance. [. . . ] The gas inlet connection is threaded ½" for external gas (ISO 228-1). Connection with a rigid copper hose: The connection to the gas supply network must be made in such a way that it does not cause stresses of any type on the appliance. The connection can be made using the adapter unit D with double cone, always inserting gasket C (provided) in between. Connection with a flexible steel hose: use only continuous wall stainless steel hoses that comply with the applicable standards, making sure to always insert gasket C (provided) between connector A and flexible hose E. [. . . ]