User manual INFINITY CASCADE THREE C

[. . . ] Keep the shipping carton and packing materials for future use. Grille Pedestal Wall Bracket 1/4"-20 Screws WHAT'S INCLUDED Model Nine Model Three V 1/4"-20 Screws Spike Kit Cleats #8 Screw Grille Pedestal Wall Bracket Grille Base Model Seven Model Three C Grille Spike Kit Cleats Foot #8 Screw Wall Bracket Grille Base 1/4"-20 Screws 2 CASCADE SPEAKER SYSTEMS PLACEMENT Stereo Before deciding where to place your Cascade speakers, survey your room and think about placement, keeping the following points in mind and using Figure 1 as a guide: · For best results, place the speakers 6' ­ 8' (1. 5m ­ 2. 5m) apart. · Position each speaker so that the tweeter is approximately at ear level. · Generally, bass output will increase as the speaker is moved closer to a wall or corner. · Refer to "Home Theater" if you also plan to use the speakers for home theater reproduction. Home Theater For front-channel use, place one speaker on the left and another on the right, along either side of the television monitor. [. . . ] For carpets, screw the round end of a foot into each hole and fully handtighten a nut onto each one. For hard-surface floors, screw the spike end into each hole instead and leave the rounded end exposed. If needed, adjust the feet so each speaker is level and then tighten each nut with the enclosed wrench. To protect hard surfaces (e. g. , wood floors), slip a nylon dome onto each round end. Note: Spiked feet must be fully threaded into holes provided in the base to ensure stability. Locking Nut SEE DETAIL A DETAIL A 5/8" min. Spike End Foot 5/8" Round End Nylon Dome (included for use on wood floors) Model Three V 1. Securely fasten one cleat to the middle set of holes on the rear of the speaker using two included 1/4"-20 panhead screws. Slide speaker with cleat over the base. CARPETED FLOORS HARD-SURFACE FLOORS This cross section shows how to install the spikes onto the bottom of a Cascade Model Nine and Model Seven. + + Model Five 1. Securely fasten one cleat to the set of holes above the terminal using two included 1/4"-20 panhead screws. Slide speaker with cleat over the base. + + 4 CASCADE SPEAKER SYSTEMS WALL-MOUNTING NOTE: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the speakers. Attaching the Grilles The Cascade loudspeakers use a unique frameless grille. Simply curl the magnet assembly behind the grille cloth, place one end of the grille just above the tweeter and then gently pull the grille taut, attaching the other end of the grille just below the woofer. Model Three V, Model Three C, Model Five 1. Attach wall bracket to wall at desired location. Model Three C Model Five Model Three V 2. Securely fasten the two cleats to the rear of the speaker, using the outermost holes, using two included 1/4"-20 panhead screws per cleat. + + 3. Carefully slide the cleats on the rear of the speakers over the tabs of the wall bracket. wall CASCADE SPEAKER SYSTEMS 5 WIRING THE SYSTEM IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). NOTE: If desired, consult your local Infinity dealer about speaker wire and connection options. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown in Figure 4. See the owner's guides that were included with your amplifier or receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i. e. , + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Figure 5. This example shows how to connect bare wires to the terminals. Banana plugs may also be inserted directly into the rear of the connector. Figure 4. This figure shows how to connect bare wires to the terminals. Figure 6. [. . . ] NOTE: Do not use any cleaning products or polishes on the cabinet or grille. Single-Stereo Amplifier If a problem occurs, make sure that all connections are properly made and clean. If a problem exists in one loudspeaker, reverse the connection wires to the left and right system. If the problem remains in the same speaker, then the fault is with the loudspeaker. If the problem appears in the opposite speaker, the cause is in another component or cable. [. . . ]