Detailed instructions for use are in the User's Guide.
[. . . ] PRIMUS SPEAKER SYSTEMS
Owner's Guide Primus 140 Primus 150 Primus 160
INFINITY PRIMUSTM SERIES
The Primus series of loudspeakers continues Infinity's longstanding commitment to accurate sound reproduction. Our proprietary Metal Matrix Diaphragm (MMDTM) drivers, precision dividing networks, and rigid, well-braced enclosures combine to deliver uncompromised performance in any stereo or multichannel home theater system. In addition, Primus series speakers are magnetically shielded for safe placement adjacent to a television.
Home Theater
For front-channel use, place one speaker on the left and another on the right, along either side of the television monitor. [. . . ] Experiment with speaker placement to obtain the best bass level and stereo imaging in your room.
Left Surround Channel
Figure 3. This figure shows an alternate layout, which may be more suitable for some rooms.
2
PRIMUS SPEAKER SYSTEMS
Co u
ch
WALL-MOUNTING THE PRIMUS 140 AND PRIMUS 150
The Primus 140 and Primus 150 are designed to mount directly to a wall. Each speaker will require (2) 1-1/2, " #10 wood screws fastened to a wall stud. If a wall stud is unavailable, install an anchor appropriate for a 1-1/2, " #10 screw. NOTE: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the speakers.
WIRING THE SYSTEM
IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a minimum #16-gauge speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). NOTE: If desired, consult your local Infinity dealer about speaker wire and connection options. The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in Figure 5. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown in Figure 6. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i. e. , + to or to +) when making connections. Doing so will cause poor imaging and diminished bass response.
FIGURE 4.
Keyhole mounts
1/4"-20 Threaded insert (Primus 140 only)
+
Step 1. Mark the positions on the wall where you would like to place the mounting screws. Fasten two 1-1/2, " #10 wood screws to the wall using the markings placed in Step 1 as your guide. Place the speaker on the wall by aligning the keyholes on the back of the speaker to the screwheads on the wall. Once positioned properly, the speaker should slide down slightly and become secure. The Primus 140 also allows the use of third-party wall brackets using the 1/4" threaded insert located beneath the keyhole mount. [. . . ] Nearby reflecting surfaces can adversely affect stereo-imaging quality. If this happens, try angling the speakers slightly inward toward the listening position until the optimum effect is achieved.
CARE OF YOUR SPEAKER SYSTEM
Each Primus series cabinet has a wood-grain-vinyl finish that does not require any routine maintenance. NOTE: Do not use any cleaning products or polishes on the cabinet or grille.
4
PRIMUS SPEAKER SYSTEMS
SPECIFICATIONS
Primus 140
Frequency Range: Recommended Amplifier Power Range: Sensitivity:
(2. 83V @ 1 meter) 100Hz 20, 000Hz (±3dB)
Primus 150
58Hz 20, 000Hz (±3dB)
Primus 160
49Hz 20, 000Hz (±3dB)
10 100 watts 86dB
10 100 watts 88dB
10 150 watts 90dB
Nominal Impedance: Crossover Frequency: Low-Frequency Driver: Mid-Frequency Driver: High-Frequency Driver: Dimensions (H x W x D):
(with grille)
8 3000Hz; 24dB/octave 4" (100mm) MMD, TM magnetically shielded N/A 3/4" (19mm) MMD, TM magnetically shielded 9-5/8" x 5-15/16" x 6-13/16" (245mm x 150mm x 173mm) 7 lb (3. 2kg)
8 3300Hz; 24dB/octave 5-1/4" (130mm) MMD, TM magnetically shielded N/A 3/4" (19mm) MMD, TM magnetically shielded 12-3/4" x 7-3/8" x 10-1/2" (322mm x 187mm x 267mm) 13. 5 lb (6kg)
8 3000Hz; 24dB/octave 6-1/2" (165mm) MMD, TM magnetically shielded N/A 3/4" (19mm) MMD, TM magnetically shielded 14-1/2" x 8-1/4" x 11" (370mm x 208mm x 280mm) 16. 1 lb (7. 3kg)
Weight:
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice.
Declaration of Conformity
We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France
declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1997
Robin Marshall Harman Consumer International Chateau-du-Loir, FRANCE 4/03
PRIMUS SPEAKER SYSTEMS
5
NOTES
6
PRIMUS SPEAKER SYSTEMS
NOTES
PRIMUS SPEAKER SYSTEMS
7
© 2003 Harman International Industries, Incorporated Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 800. 553. 3332 (USA only) www. infinitysystems. com Infinity is a registered trademark, and Infinity Primus and MMD are trademarks, of Harman International Industries, Incorporated. [. . . ]