User manual INFINITY SW-12

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual INFINITY SW-12. We hope that this INFINITY SW-12 user guide will be useful to you.


INFINITY SW-12 : Download the complete user guide (885 Ko)

Manual abstract: user guide INFINITY SW-12

Detailed instructions for use are in the User's Guide.

[. . . ] Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock. [. . . ] P/N:352153-001 POWER ON < OFF R ¤ L HIGH LEVEL OUT Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W _ + Bass Optimization Controls (see page 5) ¡ Bass Optimization System Selector TM Center-Frequency Adjustment £ Bass Optimization System Level Adjustment ¢ Bass Optimization System Bandwidth Adjustment Phase Switch § Normal/LFE Selector ¶ Power Indicator · Crossover Adjustment ª Subwoofer Level (Volume) Control , Line-Level Inputs / High-Level (Speaker) Inputs ¤ High-Level (Speaker) Outputs < Power Switch SW-12 2 CONNECTIONS If you have a Dolby* Digital or DTS® receiver/processor with a low-frequency-effects (LFE) output: If your receiver/amplifier does not have subwoofer outputs for the left and right channels or an LFE output: SUBWOOFER OR LFE OUTPUT RECEIVER/AMPLIFIER Front Speaker Output BASS OPTIMIZATION SYSTEM FREQUENCY 180 PHASE 0 LFE Normal LEVEL ON OFF POWER WIDTH GREEN: ON RED: STANDBY 50 150 CROSSOVER MIN MAX LEVEL ® BASS OPTIMIZATION SYSTEM LINE LEVEL IN R L SW-12 CAUTION R HIGH LEVEL IN L RISK OF ELECTRIC SHOCK DO NOT OPEN FREQUENCY 180 PHASE Normal 0 LFE LEVEL ON OFF POWER WIDTH WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. POWER ON OFF 0 GREEN: ON RED: STANDBY AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ. P/N:352153-001 50 150 CROSSOVER MIN MAX LEVEL ® R HIGH LEVEL OUT L Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W LINE LEVEL IN R L R HIGH LEVEL IN L SW-12 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN _ + WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. POWER ON OFF AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ. P/N:352153-001 · Set Normal/LFE Switch to LFE. _ + R HIGH LEVEL OUT L Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W NOTE: In this case, you do not need to use a Y connector. Simply connect the LFE output on your receiver/processor to either the left or right input on the subwoofer. If your receiver/processor has subwoofer outputs for the left and right channels: · Set Normal/LFE Switch to Normal. RECEIVER/PROCESSOR RED = + BLACK = BASS OPTIMIZATION SYSTEM ­ 1. LOOSEN TERMINALS FREQUENCY 180 PHASE 0 LFE OFF POWER Normal LEVEL ON GREEN: ON RED: STANDBY WIDTH 2. INSERT BARE END; TIGHTEN TERMINALS 50 150 CROSSOVER MIN MAX LEVEL ® LINE LEVEL IN R L R HIGH LEVEL IN L SW-12 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN STRIPE = POWER ON OFF ­ NO STRIPE = + WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ. P/N:351153-001 R HIGH LEVEL OUT L Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W _ + · Set Normal/LFE Switch to Normal. NOTE: Some receivers have a single subwoofer output (do not confuse this with a single LFE output as described below). In that case, it is recommended that you use a Y connector (not included) to maximize performance. 3 SW-12 OPERATION Power On Plug your subwoofer's AC cord into a wall outlet. Initially set the Subwoofer Level (Volume) Control ª to the "min" position. Turn on your sub by pressing the Power Switch < on the rear panel. Crossover Adjustments NOTE: This control will have no effect if the Normal/LFE Selector Switch § is set to "LFE. " If you have a Dolby Digital or DTS processor/receiver, the Crossover Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer Level (Volume) Control ª until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive. SW-12 4 BASS OPTIMIZATION SYSTEMTM Infinity's Bass Optimization System is a simple-to-use, yet sophisticated, low-frequency calibration system. The subwoofer contains a parametric equalizer that you can adjust following the directions below. By following these instructions, you can improve the sound of your system. To solve a problem, it helps to first identify whether you have one and, if so, what it is. First, play a variety of music and films with energetic bass sounds, like bass guitar, kick drum, keyboards, etc. [. . . ] · If you are using a multichannel surround processor or receiver, make sure all bass-management features are properly set. The Audio channels should all be set to "Small" or "HighPass" and the subwoofer set to "On. " · Set the Bass Optimization System Selector ¡ to "On. " For best results, it is recommended that all major furnishings are in place and that all doors and windows in the listening area are in their normal positions. That is, if you normally listen to music with all doors closed, then this is how they should be during this procedure. 5 SW-12 plays the tones from the test CD and records the relative output level of each test tone, using the sound-level meter, on the provided measurement template. After all the tones are complete, the template contains a response curve for the frequencies below 100Hz. The user simply notes the frequency of the largest bass peak, calculates the correct amount of attenuation, and uses the "Q-Finder"to determine the width of the curve. These three values are dialed into the Bass Optimization System controls located on the speaker. The entire process takes less than twenty minutes. If your dealer does not stock the Bass Optimization System test and measurement kit, you may purchase it directly from Infinity. residents can visit our Web site at www. infinitysystems. com or call 1. 516. 674. 4INF. MAINTENANCE AND SERVICE The enclosure and grille may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE INFINITY SW-12




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual INFINITY SW-12 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.