User manual INFINITY TSS-SAT4000

[. . . ] TSS-4000 TOTAL SPEAKER SOLUTIONS TSS-SAT4000 Owner's Guide TSS-SAT4000 OWNER'S GUIDE Table of Contents 3 4 4 5 5 8 9 10 Introduction Planning Your System Placement Installation Tabletop/Shelf Placement Assembly Wall-Mounting the TSS-SAT4000 Using the Included Wall Bracket Wiring the Speaker Specifications 2 TSS-SAT4000 INTRODUCTION Infinity Total SolutionsTM Infinity Total Solutions continues Infinity's longstanding commitment to accurate sound reproduction. Our proprietary Metal Matrix DiaphragmTM (MMD®) drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromised performance in any stereo or multichannel home theater system. [. . . ] We understand that you may be anxious to play your new system, so we have made every effort to simplify the installation and connections of the TSS-SAT4000. Before proceeding, you should decide how you would like to install the TSS-SAT4000. The TSS-SAT4000 may be mounted on the included shelf stands; mounted on the wall using the included wall brackets; recessed in the wall using an optional flush-mount kit; or mounted to our optional floor stands. Tabletop/Shelf Placement Assembly Step One Choose one of the three shelf stands on which to mount the satellite. If you decide to place the stand next to a television, the television's height should be taken into consideration. If you choose either of the taller stands, follow steps two to five on page 7. 30-1/2" 27" 23-3/8" 8" 4" 7/8" Small Medium Large TSS-SAT4000 5 Step Two For Small Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. Step Three For Small Table Stand Assembly Assemble the table stand plate, the small section and the foot. Place three nuts (provided) in base of foot and secure them in place by three screws (provided) through the top of the table stand plate. (3) 1/4-20 x 7/8" Flat-Head Screws Table Stand Plate Satellite Speaker End Cap Small Section/Collar Infinity Logo Foot 1/4-20 x 3/4" Screw (3) 1/4-20 Nuts NOTE: The bottom is the side closest to the Infinity logo on the front grille and the speaker connections on the rear. Step Four For Small Table Stand Assembly Run speaker wire through base, and screw foot assembly to speaker assembly. Speaker Wire 1/4-20 x 1-1/4" Flat-Head Screw 6 TSS-SAT4000 Step Two For Medium and Large Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. Step Four For Medium and Large Table Stand Assembly Use screw and washer to attach medium or large base assembly to the speaker assembly, as shown. Satellite Speaker End Cap Infinity Logo Flat Washer NOTE: The bottom is the side closest to the Infinity logo on the front grille and the speaker connections on the rear. 1/4-20 x 1" Pan-Head Screw 1/4-20 x 3/4" Screw 1/4-20 x 3/4" Pan-Head Screw Flat Washers 1/4-20 x 1" Pan-Head Screw Step Five For Medium and Large Table Stand Assembly Run speaker wire through table stand plate. Use three screws (provided) to attach plate to bottom of base assembly. Step Three For Medium and Large Table Stand Assembly Run speaker wire through collar. Using three screws, attach table stand plate to the medium or large section as shown. (3) 1/4-20 x 7/8" Flat-Head Screws Speaker Wire Speaker Wire (3) 1/4-20 x 7/8" Flat-Head Screws TSS-SAT4000 7 Wall-Mounting the SAT-4000 Using the Included Wall Bracket The customer is responsible for proper selection and use of mounting hardware, and for correctly and safely wall-mounting the speakers. Step Four Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. Step One Remove the wall-bracket cover by removing the four wall bracket screws on the ends as shown. End Cap Satellite Speaker End Cap Infinity Logo Step Two Run the speaker wire behind the wall bracket and out the hole at the bottom. After deciding where to place the satellite speaker, attach the wall bracket (in a vertical position) to the wall using the appropriate screws and anchors. Wall Bracket NOTE: The bottom is the side closest to the Infinity logo on the front grille and the speaker connections on the rear. 1/4-20 x 3/4" Screw Mounting Screws and Anchors Not Included Step Five Connect the wires (page 9). Replace the end caps while capturing the wall bracket in between parts A and B and securing it in place. Tighten until snug. Bottom Hole Step Three Run the speaker wires out through the bottom hole of the wall bracket cover. Resecure in place as shown with four of the wall bracket screws. Wall-Mount End Cap A Wall-Mount End Cap B 8 TSS-SAT4000 Step Six The wall-bracket design allows for rotation of the speakers at angles up to 30 degrees of center. Position the speakers so they face toward the primary listening position, before fully tightening. ­ + WIRING THE SPEAKER After placing the speaker, you are ready to connect it to your system. Consult the owner's manuals, included with your amplifier or receiver, for connection and operation procedures. Figure 3. This example shows how to connect bare wires to the terminals. [. . . ] The specifications and construction details in this and related Infinity publications are therefore subject to change without notice. Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 Robin Marshall Harman Consumer International Chateau-du-Loir, France 10/04 10 TSS-SAT4000 NOTES TSS-SAT4000 11 © 2004 Harman International Industries, Incorporated Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516. 674. 4INF (USA only) www. infinitysystems. com * Trademarks of Dolby Laboratories. Infinity and MMD are registered trademarks, and Total Solutions and Metal Matrix Diaphragm are trademarks, of Harman International Industries, Incorporated. [. . . ]