User manual INFOCUS IN20

[. . . ] IN20 SERIES Reference Guide Declaration of Conformity Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands We declare under our sole responsibility that this projector conform to the following directives and norms: EMC Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC Safety: IEC 60950-1: 1st Edition March, 2006 FCC Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] The remote also has a Source button to switch between sources. navigation buttons Troubleshooting the remote · · Make sure the batteries are installed in the proper orientation and are not dead. Make sure you're pointing the remote at the projector or the screen, not the computer, and are within the remote range of 15 feet (4. 5m). For best results, point the remote at the projector. 22 Using the audio Using the projector's speaker To use the projector's speaker, connect your source to the Audio In connectors (L and/or R) on the projector's composite connectors. Troubleshooting Audio If you aren't hearing the audio, check the following: · · · · · · Make sure the audio cable is connected. Make sure that you are connected to an "audio out" connector on the source as opposed to a "line-in" or "microphone" connector. If playing a video, make sure the playback has not been paused. adjust volume connect audio cable Connecting external speakers The projector can be attached to external amplified speakers by connecting a 3. 5mm stereo audio cable from the Audio Out connector on the projector to the amplified speakers. Alternatively, you can bypass the projector's audio system and connect the audio directly from your source to a stereo or home theater system. external speakers with own power source audio out speaker cable 23 Using the keypad buttons Most buttons are described in detail in other sections, but here is an overview of their functions: Power­turns the projector on and off (page 10). Up/Down arrows­navigates to and adjusts settings in the menus (page 27). Source­changes the active source. menu navigation buttons 24 Optimizing computer images After your computer is connected properly and the computer's image is on the screen, you can optimize the image using the onscreen menus. · · · · · Adjust the Keystone, Contrast, or Brightness in the Picture menu (page 28). Adjust the Phase, Tracking, or Horizontal or Vertical position in the Advanced menu (page 29). Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 29). Presentation features Several features are provided to make giving presentations easier. · The Custom key, available on several optional remotes only, allows you to assign various features to the button. The default effect is Source Info, which displays information about the projector and current source. The Startup Logo option lets you change the default start up screen to a blank or default screen (page 32). Two options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 31). · · 25 Optimizing video images After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. · · · · · · Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu (page 28). Turn on Overscan to remove noise on the edges of the image. Customizing the projector You can customize the projector for your specific setup and needs. · · · · · · · · · For rear projection, turn rear mode on in the Settings>System menu. For ceiling mounted projection, turn ceiling mode on in the Settings>System menu. [. . . ] If the message "Incorrect PIN" appears, verify the code and re-enter it. If you mis-enter a number, you must enter 5 numbers and press the Select button in order to access the "Incorrect PIN" message and re-enter the code. To enter the PIN at projector startup: Power up the projector. The "Enter PIN" dialog box appears after the startup screen. Use the navigation buttons on the remote or keypad to enter the correct button press sequence. [. . . ]