User manual INFOCUS IN2126A

[. . . ] Declaration of Conformity Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223-8368 USA We declare under our sole responsibility that this projector conforms to the following directives and norms: ErP Directive 2009/125/EC EMC Directive 2004/108/EC EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3 Low Voltage Directive 2006/95/EC Safety: IEC 60950-1: 2005;EN 60950-1:2006 +A11:2009 FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Ceiling Mount: turns the image upside down for ceiling-mounted projection. Rear Project: reverses the image so you can project from behind a translucent screen. Blank Key: select what to display when the blank key on the remote is pressed: a solid color screen (blue, black or white), or the factory logo screen. Custom Key: allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press < or > to choose a different one. • • • • Blank Screen: displays a solid color or factory logo screen. Auto Image: resets the projector to the source. 28 Lamp. . . Programmed Dimming: When enabled, Programmed Dimming enhances contrast ratios, lamp life and system noise performance. Lamp power will change continuously based on the brightness of the program content. Note: Image anomalies may be seen when image scenes change from dark to light (or light to dark). Note: Programmed Dimming is off by default. To change the PIN: Select “Change PIN. . . ” in the Advanced Menu > Setup > PIN settings menu. Enter the new PIN. Power Power Saving Mode: When the Power Saving Mode is On and the projector is in standby (powered off but connected to AC power), external audio and the Monitor Out function will not work. AC Power On: When this feature is enabled, the projector automatically turns on when power is connected. This allows control of ceiling mounted projectors with a wall power switch. Instant Power On: When this feature is enabled and it has been less than 1 minute since the projector was powered down, you can turn the projector back on immediately. When this feature is disabled, you will need to wait for the projector lamp to completely cool before restarting the projector. Eco Blanking: When this feature is enabled and no video source is sensed, 70% of lamp power is saved and no image is shown. When the video source is again applied, the image is shown immediately. Lamp Low Power: toggles between on and off. Menu Position: allows you to change the position of the On Screen Display items. Menu Transparency: allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible. Show Messages: displays status messages (such as “Searching”) in the upper-left corner of the screen. PIN Settings PIN Protect: The PIN (personal identification number) feature allows you to password protect your projector. Once you enable the PIN feature, you must enter the PIN before you can project an image. Use the Left/Right/Up/Down arrows buttons on the remote or keypad to set a 4-button press sequence. If you enter an incorrect PIN 3 times in succession, the projector will automatically shut down. If you lose or forget your custom PIN, contact InFocus Technical Support. [. . . ] Refer all servicing to qualified service personnel. Using the security lock The projector has a security lock for use with a Cable Lock System. Refer to the information that came with the lock for instructions on how to use it. security lock 54 Replacing the projection lamp The Lamp Hours timer in the Projector Info menu counts the number of hours the lamp has been in use. • NOTE: Be sure to use the InFocus lamp module designed for this projector. You can order new lamps from www. infocus. com (in select areas), your retailer or your dealer. [. . . ]