User manual INFOCUS LP560 Reference Guide

[. . . ] LCD PROJECTOR USER'S GUIDE fold and tear here fold and tear here Connecting the LitePro is summarized on the back of this card and described in detail in the LitePro 560/570 User's Guide. R The User's Guide contains instructions and illustrations for connections to all compatible computers. It also describes the remote control buttons and menu functions. 1 You must install the projection bulbs the first time you use the LitePro. 8 Refer to the "Read Me First" card or page 40 of the User's Guide for instructions. Connect the LitePro cable to the monitor connector on your computer. If you want to display your presentation on your computer 's monitor as well as on the projection screen, attach the "MONITOR" end of the LitePro cable to the end of the monitor's cable. 2 3 4 5 6 Place the LitePro on a flat surface within six feet of your power source and your computer. Plug the "LCD" end of the LitePro cable into the "COMPUTER" connector on the side of the LitePro. [. . . ] Press the left or right arrow buttons until "Audio" is highlighted. Audio Menu The right side of each menu contains information about the state of the LitePro. If you need to call In Focus Technical Support for assistance, they may need to know these values. Highlighting Menu Functions You must highlight a function before you can change its setting. · Use the left and right arrow buttons to highlight functions. Making Changes to Menu Functions When the function you want to change is highlighted, you can change the setting. · Use the up and down arrow buttons to adjust settings up and down. 25 LitePro 560/570 User's Guide Using the LitePro · In Menu 2 and the Audio Menu, you can also use select/enter to select/de-select a function or to increase the value of a function. Removing the Menu from the Screen Press the menu button to remove the menu from the screen. Resetting Menu Functions to the Default Settings To reset all menu settings to their factory default values, select Reset from Menu 2. Refer to page 30 for more information about Reset. Menu 1 Functions Brightness Adjusting the brightness changes the color saturation. Adjusting the brightness has no effect if a computer source is not connected. Use the right or left arrow buttons to highlight "Brightness". Press the up arrow button to increase the amount of green in the image. Press the down arrow to increase the amount of red in the image. 26 LitePro 560/570 User's Guide Using the LitePro Sync The LitePro adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy, streaked or noisy, try adjusting the sync from this menu. Up/Down These functions allow you to change the vertical position of the projected image. Left/Right These functions allow you to change the horizontal position of the projected image. Use the right or left arrow buttons to highlight "Left/Right". Press the down arrow button to move it to the right. LitePro 560/570 User's Guide 27 Using the LitePro Menu 2 Functions Rear Projection When you select Rear Projection, the LitePro reverses the image so you can project from behind the screen as shown here. To enable or disable to rear projection mode: 1. Use the right or left arrow buttons to highlight "Rear Projection". (Press select/ enter again to change it back. ) Source Prompt When you are displaying your presentation and you press select/ enter to switch sources, the LitePro momentarily displays the name of the active source. If you don't want this display, follow the steps below to disable the Source Prompt. Use the right or left arrow buttons to highlight "Source Prompt". Press select/enter to enable or disable the Source Prompt. 28 LitePro 560/570 User's Guide Using the LitePro Test Pattern If the test pattern is turned on, it displays when the LitePro is first powered on and also when no computers or video players are connected to the LitePro. [. . . ] Refer to the In Focus Accessories Catalog for additional items. Item Read Me First card LitePro 560/570 User's Guide LiteShow II User's Guide Soft Carry Case Shipping Box ATA-Approved Hard Carry Case LitePro (VGA) Cable North American Power Cord Australian Power Cord UK Power Cord European Power Cord Danish Power Cord Swiss Power Cord Projection Lamps, 36V, 400W (set of 2) Lens Cover Mac Adapters (set of 2) Remote Control Programmer User's Guide Remote Control Programmer Software Remote Control Programmer (RS-232) Cable Remote Control Programmer (RS-232) Adapter RCA jack-to-mini plug adapter Remote Control LitePro Ceiling Mount Kit LiteShow Demo Disk LiteShow System Disk Fuse, 10A, 3AB (use w/110V) Fuse Holder for 10A, 3AB Fuse (use w/110V) Fuse, 6. 3A, 5x20mm (use w/220V) Fuse Holder for 6. 3A, 5x20mm Fuse (use w/220V) Part Number 009-0124-xx 010-0060-xx 010-0061-xx 110-0079-xx 110-0080-xx 591-0169-xx 210-0014-xx 210-0023-xx 210-0027-xx 210-0028-xx 210-0029-xx 210-0030-xx 210-0031-xx 232-0020-xx 340-0148-xx 516-0003-xx 010-0083-xx 599-0064-xx 210-0055-xx 515-0025-xx 515-0034-xx 590-0095-xx 591-0098-xx 599-0063-xx 599-0062-xx 749-0013-xx 749-0014-xx 749-0010-xx 749-0011-xx LitePro 560/570 User's Guide 53 Appendix Cable Connector Pin Assignments The Y-shaped LitePro cable that shipped with your LitePro has three connectors, they are labeled "Monitor", "Computer" and "LCD. " The pin assignments for these connectors are listed here. "LCD" Connector The end of the LitePro cable that plugs into the LitePro itself is a male 26-pin D-style connector. The table below lists its pin assignments. Input Pin 1 2 8 6 7 9 16 17 18 20 21 22 23 24 25 Signal Description Vertical sync Horizontal sync Blue analog reserved reserved Red analog reserved reserved Green analog GND GND GND Digital/analog video cable ID GND VGA/no video cable ID pin Output Pin 10 11 14 12 13 15 3 4 5 54 LitePro 560/570 User's Guide Appendix "Monitor" and "VGA" Connectors The pin assignments are the same for the "Monitor" and "VGA" connectors. The "Monitor" connector is a female video RGB, 15-pin micro-D-style connector. [. . . ]