User manual IOGEAR GHE135U INSTALL GUIDE

[. . . ] IOGEAR® makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. IOGEAR® assumes no responsibility for any inaccuracies or errors that may appear in this document. Reproduction in whole or part without permission is prohibited. Table of Contents: Table of Contents Package Contents Overview Features Requirements Introduction Installation (Hard Drive, ION Drive Software) Connecting ION Drive to Your Computer Device Removal Driver Removal Care & Handling Trouble Shooting Technical Support Appendix Specification Radio & TV Interference Statement Limited Warranty 02 03 04 05 06 10 20 22 24 26 27 29 30 31 32 33 Package Contents This package contains: 1 IONTM Drive 1 Hi-Speed USB 2. 0 Type A to B Cable (6 feet) 1 IOGEAR Installation CD 1 Power Adapter 1 User Manual 1 Warranty Card If any of the items are missing or damaged please contact your dealer immediately. 2 Overview Overview The IONTM Drive is yet another innovative Hi-Speed USB 2. 0 solution developed by IOGEAR®. [. . . ] 2 Remove Base Remove Phillips screw from bottom edge of side panel. Note: For the best performance for the USB 2. 0 device, please use the cerified USB 2. 0 cable provided with this product. 10 Installation of Hard Drive Step. 4 Remove two screws in hard drive retention bracket. 11 Installation of Hard Drive Step. Slide in an upward direction towards the top of the enclosure to free the drive bracket. Lift the drive bracket out of the enclosure. 12 Installation of Hard Drive Step. USB A to B cable 1 2 3 4 5 6 7 8 13 Installation of Hard Drive Step. Screw the four screws into the drive bracket that were provided with the hard drive. Make sure you take all the necesssary steps to avoid ESD (electric static discharge). 14 Installation of Hard Drive Step. 8 Attach the signal cable to the hard drive connector of the hard drive with bracket attached. Attach the bracket with drive attached into the enclosure and seat over the base plate. Line up the holes in bracket with the base plate. 15 Installation of Hard Drive Step. 9 Insert two screws through bracket and tighten down bracket to base plate. 16 Installation of Hard Drive Step. 10 Place side cover on enclosure and secure by sliding in forward direction. 11 Place assembled enclosure back into the base. 17 Installation of ION Drive Software Step. Insert the IOGEAR Installation CD into your computer's CDROM tray (It is not necessary to install this driver under Window 2000, ME, and XP). Step. 2 Select "ION" in My Computer. 18 Installation of ION Drive Software (Continued) Step. 5 We recommend to choose "Complete" when prompted how to install. Step. 6 After the installation, you will be able to find the hard drive in My Computer after you turn on the power of ION. 19 Connecting ION Drive to Your Computer 1 2 Note: Before you begin, please make sure that the power to the device and your computer has been turned off. Plug the Hi-Speed USB 2. 0 cable with Type A connector into the back of the IONTM Drive Step 2. Plug the Power Adapter into the back of the IONTM Drive 20 Connecting ION Drive to Your Computer 1 Step 3. Plug the Hi-Speed USB 2. 0 Cable (Type A Connector) into the Hi-Speed USB 2. 0 Port (Type A Slot) located on the back of your computer in the PCI Card Bays. Your computer will automatically identify the IONTM Drive and load all necessary drivers. 21 Device Removal Step. 1 Before you unplug the ION drive, click on the green arrow on the lower right corner of the Window. Step. [. . . ] Spin down - The act of the disk inside the drive or cartridge ceasing its rotation. Spin up - The act of the disk inside the drive getting up to the proper rotations per minute. The disk inside the drive must spin at the proper speed for the disk to work. 30 Specification Product Specification (MODEL: GHE135U) Function Power Consumption Input Voltage Connector Type Storage Temperature Operating Temperature Operating Humidity Dimensions Weight EMI Specification 15w 12V DC, 1. 6A USB 2. 0 Type A 0-70 C (Celsius) 0-50 C (Celsius) 20 to 89% (Non Condensing) 3. 5" x 6. 0" x 8. 0" 1. 5 pounds FCC Class B 31 Radio & TV Interference Statement Radio & TV Interference Statement WARNING!!!This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. [. . . ]