User manual IOGEAR GHE835C

[. . . ] IOGEAR® makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. IOGEAR® assumes no responsibility for any inaccuracies or errors that may appear in this document. Reproduction in whole or part without permission is prohibited. Table of Contents Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Moving data at the blazing speed of 800Mbps and 480Mbps these allow high-speed devices to take full advantage of the bandwidth and reliability offered by these new technologies. 6 Introduction This manual contains information on the installation and capabilities of your new IONTM Drive. In sections of the manual where sequential steps are listed, each action is listed with no indentation. Additional text is included, but indented, to further explain each of these actions. A glossary has been added at the end of the manual so you may look up unfamiliar terms. A few things should be mentioned before explaining the installation procedure: All IOGEAR® IONTM drives are tested prior to shipment to ensure product quality. The connectors on a FireWire® 800 and Hi-Speed USB 2. 0 cable are designed in such a way as to prevent plugging the cable in upside down, backwards, or into a different type of connector. At time of print, some computers do not have FireWire® 800 and Hi-Speed USB 2. 0 capabilities. To ensure optimum compatibility, please make sure your computer is FireWire® 800 and USB 2. 0 compatible, or have had an FireWire® 800 and USB 2. 0 upgrade card added to your computer system. 7 Pictorial Introduction Front View 1 1. IONTM Base 2 3 8 Pictorial Introduction Back View 1 2 3 1. Power Port 9 Installation If you purchased the enclosure only model (GHE835C), please follow these instructions on page 11 to install your 3. 5" Hard Disk Drive. WARNING: Opening an IONTM Drive with a built-in Hard Drive (GHD835C80, GHD835C120, etc. . . ) WILL VOID YOUR WARRANTY. For assistance with your hard drive, please contact your IOGEAR Service Support representative. 10 Installation Hardware Installation: Attention!Please take all proper Electro Static Discharge (ESD) precautions during the installation of your new hardware. 1 Please have the following ready 1 Phillips screw driver (not included in the package) Step. 2 Remove Base Remove Phillips screw from bottom edge of side panel. 11 Installation Step. 4 Remove two screws in hard drive retention bracket. 12 Installation Step. Slide in an upward direction towards the top of the enclosure to free the drive bracket. Lift the drive bracket out of the enclosure. 13 Installation Step. Side panel Enclosure with one side panel attached Drive bracket One small screw Two long screws with nylon collar AC adapter AC adapter cord USB 2. 0 A to B cable 1 FireWire (9-pin to 9-pin) cable 2 3 4 5 6 7 8 9 14 Installation Step. Screw the four screws into the drive bracket that were provided with the hard drive. 15 Installation Step. Place the bracket with drive attached into the enclosure over the base plate. Line up the holes in the bracket with the base plate 16 Installation Step. [. . . ] Spin down - The act of the disk inside the drive or cartridge ceasing its rotation. Spin up - The act of the disk inside the drive getting up to the proper rotations per minute. The disk inside the drive must spin at the proper speed for the disk to work. 24 Specification Product Specification 25 Radio & TV Interference Statement WARNING!!!This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. [. . . ]