User manual IOGEAR GVS98

[. . . ] DC Power Jack 1 7 8 2 9 10 3 4 5 6 11 12 13 14 *Note: IR Extender not included. **Note: For the audio part of a Component media source, please use the PC Audio Input Port with a 3. 5mm to RCA Cable (Not included and sold separately ­ IOGEAR Part No: G2LMMRCA006). 6 Wall Mount Hang the unit on the wall by using the two screw holes on the unit. 1 2 7 Installation Note: Please make sure your displays and media sources are turned off before you start. 1 HDMI Media Source Connect a HDMI cable from the media source's HDMI output to the transmitter unit's HDMI input 2 VGA Media Source Video ­ Connect a VGA cable from the media source's VGA output to the transmitter unit's VGA input Audio ­ Connect a 3. 5mm stereo audio cable (Not included and sold separately IOGEAR Part No: G2LMM006) from the media source's audio output to the transmitter unit's PC Audio-In port 3 Composite Media Source Connect a composite cable from the media source's composite output to the transmitter unit's composite input 4 Component Media Source Video ­ Connect the included Component to VGA Adapter to the VGA Input of the transmitter unit, then connect a Component video (YPbPr) cable from the media source's Component output to Component connection of the Component to VGA Adapter Audio ­ Connect a 3. 5mm to RCA cable (Not included and sold separately ­ IOGEAR Part No: G2LMMRCA006) from the media source's audio output to the transmitter unit's PC Audio-In port VCR 1 Blu-ray Player 3 2 4 4 DVR PC 8 Step 2 Connect the IR Blast to the IR-Out Port from the Transmitter unit. [. . . ] 1 HDMI Media Source Connect a HDMI cable from the media source's HDMI output to the transmitter unit's HDMI input 2 VGA Media Source Video ­ Connect a VGA cable from the media source's VGA output to the transmitter unit's VGA input Audio ­ Connect a 3. 5mm stereo audio cable (Not included and sold separately IOGEAR Part No: G2LMM006) from the media source's audio output to the transmitter unit's PC Audio-In port 3 Composite Media Source Connect a composite cable from the media source's composite output to the transmitter unit's composite input 4 Component Media Source Video ­ Connect the included Component to VGA Adapter to the VGA Input of the transmitter unit, then connect a Component video (YPbPr) cable from the media source's Component output to Component connection of the Component to VGA Adapter Audio ­ Connect a 3. 5mm to RCA cable (Not included and sold separately ­ IOGEAR Part No: G2LMMRCA006) from the media source's audio output to the transmitter unit's PC Audio-In port VCR 1 Blu-ray Player 3 2 4 4 DVR PC 8 Step 2 Connect the IR Blast to the IR-Out Port from the Transmitter unit. Then stick the IR blast directly in front of each of the IR sensor of your media source devices Note: If the location of the IR sensor for your media source is not found, you can point the media source's remote directly in front of the media source, then search for the IR sensor's location by controlling the media source in different area in the front panel until you find the spot that the media source can be able to received the signal from the remote control. 9 Step 3 Connect the receiver unit to your display with either one of the three different connections. 1 HDMI Connect a HDMI cable from the receiver unit's HDMI output to your display's HDMI input 2 Composite Connect a Composite cable from the receiver unit's AV output to your display's Composite input 3 Component Video ­ Connect a Component Video (YPbPr) cable from the receiver unit's Component output to your display's Component input Audio ­ Connect a 3. 5mm to RCA Cable (Not included and sold separately ­ IOGEAR Part No: G2LMMRCA006) from the receiver unit's PC Audio Output port to RCA ports of the component input of your display TV Back 1 2 3 Step 4 Connect the power adapters from the wall outlet to the transmitter unit and receiver unit. Then the transmitter unit and receiver unit will turn on automatically. 10 Step 5 Turn on your display Step 6 The Power/Link LEDs on the transmitter unit and receiver unit should be flashing, wait till the connection is established (this usually take about 1 to 2 minutes), then you will see the Power/Link LED will stop flashing which means the connection between the transmitter unit and receiver unit is successfully established. You should now see the IOGEAR startup screen on your display, if not, please refer to the Tips at the end of this section for troubleshooting. Step 7 Select the specific input from the transmitter unit and the specific output from the receiver unit by using the remote control or the front panel pushbutton from the units. If the transmitter unit and receiver unit are not establishing the wireless connection: a. If they are already in the same WiFi Channel, try to unplug the power on both transmitter unit and receiver unit and plug it back in to perform a power cycle to let them reset themselves. The signal will then send from the receiver unit back to the transmitter unit. Finally, it will send to your media source via the IR blast. IR Extender This is an optional feature that allows you to hide the receiver unit and still able to control your media sources Video Format Support This product supports both digital and analog video format: Digital Video: HDMI ­ Up to 1080p60 Analog Video: Composite ­ Up to 480p Component ­ Up to 1080i60 VGA ­ Up to 1920x1080@60Hz Audio Format Support This product supports both digital and analog audio: Digital Audio ­ AC-3 Dolby Digital, DTS (Pass Through) Analog Audio ­ 16bit 2-Channel linear PCM (44. 1kHz & 48kHz) 15 Connection Between the Transmitter Unit and Receiver Unit There are two different kinds of connection between the transmitter unit and receiver unit 1. WiFi ­ Wireless Connection This is a wireless connection and there are 2 channels to choose from. The default channel is Channel 1; however if you are experiencing any interferences while using Channel 1, you can change it to Channel 2. WiFi Channel Channel 1 Channel 2 Frequency Use 5. 19GHz (WiFi Ch 38) 5. 23GHz (WiFi Ch 46) 2. LAN - Wired Connection This is a wired connection that requires a solid CAT5e/6 patch cable to be connected to the LAN ports between the transmitter unit and receiver unit Factory Reset This will changes all the settings back to the original default settings. Step 1 Remove the DC power from the transmitter or receiver unit Step 2 Press and hold the Front Panel Pushbutton, then while holding the pushbutton, re-connect the DC power to the transmitter unit or receiver unit Step 3 Keep holding the pushbutton until you see all the LEDs on the unit are flashing rapidly Final Step Release the pushbutton then wait for the unit to be reset 16 Firmware Upgrade / Configuration Update Please visit our website at http://avior. iogear. com/support/custom/wirelesshdkit and follow the instructions to upgrade the firmware or configure the units*. Note: Please make sure all units are using the same firmware version in order to function correctly. *Note: The transmitter unit and receiver unit set has been pre-configured to Peer-to-Peer Mode. [. . . ] Note: Please make sure all units are using the same firmware version in order to function correctly. *Note: The transmitter unit and receiver unit set has been pre-configured to Peer-to-Peer Mode. There is no need to re-configure unless you need to change the set into Broadcasting Mode. Streaming Mode Peer-to-Peer Mode This is a 1 to 1 streaming mode, which is the default setting of the set. [. . . ]