User manual IOGEAR MINIVIEW GCS102U

[. . . ] ATEN Technology makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. ATEN Technology assumes no responsibility for any inaccuracies or errors that may appear in this document. Packing List & System Requirements This complete IOGEAR MiniViewTM package consists of: · · · · · One MiniViewTM: USB KVM switch Two or four USB A-B cables Two or four VGA cables One DC 5V Power Adapter One User Manual & Quick Setup Guide Please check to make sure that all components are included and nothing is damaged. Before connecting your MiniViewTM, read the manual thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the unit and/or any devices it connects to. [. . . ] Connected PC's can be added or removed from the setup without powering off the KVM switch. 3 Year Limited Warranty. Features 2 Specifications Port Se le ction LEDs Ho t K eys / Port Se le ction But ton Po rt-Se le cte d M onito r HDB -15 VGA (F) Type -A (D owns tre am) HDB -1 5 VGA (M ) Type -B (Ups tre am) M a x: 192 0 x 14 40, D D C2B 3 or 15 s e conds D C 5V 1 5mA Plas tic / M e ta l 5°C ~ 40°C - 20°C ~ 60°C 0 ~ 80 % RH, Nonc onde ns ing G- CS102U: 4 . 9 ounce s G-CS1 04U: 38 . 83 ounce s Co ns ole Conne c tors US B M onito r PC Conne c tors US B Vide o Re s olution A ut oScan Int e rv al Powe r Cons umpt ion Hous ing Ope rating Te mpe rature Storage Te mpe rature Humidity We ight D ime ns ions (L x W x H) G-CS10 2U: 4. 0" Specifications 3 Overview Front View: 1 Selected LEDs These LEDs indicate the currently selected port. 2 Auto Scan LED The Auto Scan LED flashes when Auto Scan Mode is in effect. 3 Port Selection Switch The Port Selection Switch is located on the front panel, just opposite the Select Arrow on the front panel. The Selected LED on the front panel lights to indicate which port is selected. On-Line LEDs These LEDs indicate that a computer is properly connected to the switch, powered on and operational. Auto Scan Switch This push button toggles Auto Scan Mode for the MiniViewTM: USB. Overview 4 Overview. . . Overview 1 4 5 2 3 5 Overview. . . Rear View 1. ) Console Video Connector Connect your monitor here. 2. ) Power Jack If you choose to use an external DC 5V power adapter, connect it here. 3. ) Scan Time Selection Switch This slide switch selects the amount of time the MiniViewTM: USB will monitor each port (3 or 15 seconds) when Auto Scan Mode is enabled. 4. ) Downstream USB Ports Connect your USB keyboard, USB mouse and two other USB devices here. 5. ) Upstream USB Ports These Upstream ports connect to your Mac or PC to provide the necessary connection between the MiniViewTM: USB and the computer. 6. ) PC Video Ports These video ports connect to your iMac, G3/G4 or PC to provide the necessary connection between the MiniViewTM: USB and the computer. Overview 6 Overview. . . Overview. . . 2 1 3 4 6 5 Overview 7 Installation Before you begin, make sure that power to your computers and peripherals (monitor, scanner, etc. ) is turned off. 1. ) Connect your monitor to the Console Video Port on the MiniViewTM: USB. 2. ) Connect your USB peripherals to the USB Downstream Ports on the MiniViewTM: USB. 3. ) If you choose to use an external 5V power adapter, plug the adapter into an AC source, then plug the adapter cable into the Power Jack on the MiniViewTM: USB. 4. ) Use the video extender cables to connect the MiniViewTM: USB's video ports to the video ports on the corresponding computers. 5. ) Use the USB A-B cables to connect the Upstream Ports on the MiniViewTM: USB to available Downstream USB ports on your computers. If the computer attached to Port 1 is inactive, the monitor will be blank so it may appear as if the unit is not functioning. [. . . ] IOGEAR 16560 Aston Street Irvine, CA 92606 Phone: (949) 250-1260 Toll Free: (888) 999-2836 Fax: (949) 250-1262 www. iogear. com info@iogear. com Appendix B 13 Appendix C Radio & TV Interference Statement This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee, however, that interference will not occur in a particular installation. [. . . ]